Workshop Repair Manuals

Ford Workshop Manuals

[PREV PAGE] [NEXT PAGE]

ford Workshop Repair Guides


Mondeo 2001 (10.2000-02.2007)

Mechanical Repairs > 3 Powertrain > 303 Engine > 303-01C Engine - 2.5L Duratec-VE (VE6) > Specifications

Engine - 2.5L Duratec-VE (VE6) - Specifications Mondeo 2001 (10/2000-02/2007)

Engine Data

Description
Firing order 1-4-2-5-3-6
Engine management Black-Oak
Emission standard Stage IV
Engine code LCBD
Bore (mm) 81.66
Stroke (mm) 79.5
Displacement (cm 3 ) 2499
Compression ratio 9,7:1
Power output kW /PS 125/170
Power output at (rpm) 6250
Torque (Nm) 220
Torque at (rpm) 4250
Idle speed (rpm) 700
Number of crankshaft main bearings 4
Number of camshaft bearings 4
Camshaft operation Chain
Intake valve clearance Hydraulic adjustment
Exhaust valve clearance Hydraulic adjustment
Spark plug AGSF 32 FM
Maximum oil consumption 0.5 l/ 1000 Km

Engine Oil

Description Viscosity Specification
Recommended engine oil
Ford Formula E SAE 5W-30 WSS-M2C913-B
Alternative engine oils
Ford Formula S SAE 5W-40 ACEA A3/B3
Ford XR+ High Performance SAE 10W-40 ACEA A3/B3

Lubricants, Fluids, Sealers and Adhesives

Item Specification
Coolant WSS-M97B44-D
Power steering hydraulic fluid WSA-M2C195-A
Sealant WSK-M4G323-A4
Sealant ESE-M99B144-B

Capacities - Vehicles built up to 06/2003

Litres
Engine oil, initial fill including oil filter 6.0
Engine oil, including oil filter change 5.5
Engine oil, excluding oil filter change 5.0

Capacities - Vehicles built 06/2003 onwards

Litres
Engine oil, initial fill including oil filter 6.2
Engine oil, including oil filter change 5.7
Engine oil, excluding oil filter change 5.2

Cylinder Block

Description mm
Cylinder block bore diameter, class 1 81.640 - 81.650
Cylinder block bore diameter, class 2 81.651 - 81.660
Cylinder block bore diameter, class 3 81.661 - 81.670

Crankshaft

Description mm
Crankshaft end play 0.135 - 0.255

Camshafts

Description mm
Bearing journal diameter 26.926 - 26.936
Bearing inside diameter 27.012 - 26.897
Camshaft end play 0.025 - 0.165

Valves

Description mm
Valve stem clearance (exhaust) 0.045 - 0.094
Valve stem clearance (intake) 0.020 - 0.069
Valve head diameter (exhaust) 26
Valve head diameter (intake) 32

Cylinder Head

CAUTION:
CAUTION:The mating face of the cylinder head must not be reworked.
Description mm
Maximum distortion (mating face) 0.08

Lubrication System

Description bar
Maximum oil pressure at 1500 rpm 3.1

Torque Specifications

Description Nm lb-ft lb-in
Transaxle retaining bolts 40 30 -
Engine mount bracket retaining bolts 47 35 -
Front engine mount retaining bolts 83 61 -
Rear engine mount retaining bolts 80 59 -
Engine support insulator center bolt 80 59 -
Front exhaust pipe retaining bolts 40 30 -
Rear catalytic converter retaining nuts 40 30 -
Left and right-hand top mount retaining nut 59 44 -
Starter motor bracket retaining bolts 48 35 -
Ground cable to automatic transmission housing 40 30 -
Mounting plate to cylinder block 47 35 -
Oil pump blanking plug 10 - 89
Oil pump cover retaining bolts 10 - 89
Oil pump retaining bolts 10 - 89
Oil baffle retaining nuts 10 - 89
Oil pick-up pipe retaining nut 5 - 44
Oil pick-up pipe retaining bolts 10 - 89
Oil separator retaining bolts 10 - 89
Oil drain plug 26 19 -
Oil pan retaining nuts and studs 25 18 -
Oil pressure switch 14 10 -
Oil dipstick tube bracket to coolant distribution pipe
10 - 89
Cylinder head retaining bolts a) - -
Camshaft bearing caps retaining bolts 10 89
Camshaft seal retainer retaining bolts 10 89
Timing chain guide retaining bolts 25 18 -
Timing chain tensioner retaining bolts 25 18 -
Engine front cover retaining bolts and studs 25 18 -
Wiring harness bracket to engine front cover 10 - 89
Camshaft position (CMP) sensor retaining bolt 10 - 89
Crankshaft position (CKP) sensor retaining bolt 10 - 89
Crankshaft pulley retaining bolt a) - -
Power steering pump retaining bolts 25 18 -
Power steering pump retaining nuts 10 - 89
Power steering pump bracket retaining bolts 47 35 -
Power steering pump pulley retaining bolts 25 18 -
Spark plugs 15 11 -
Valve cover retaining bolts 10 - 89
Wiring harness retaining plate to valve cover 10 - 89
Exhaust manifold to cylinder head a) - -
Generator bracket retaining bolts 25 18 -
Generator retaining bolts 48 35 -
Flex plate retaining bolts 80 59 -
Flywheel retaining bolts 80 59 -
Camshaft seal retainer retaining bolts 10 - 89
Coolant pump to cylinder head a) - -
Coolant connecting pipe to cylinder head 10 - 89
Positive crankcase ventilation (PCV) bracket to coolant connecting pipe 6 - 89
Coolant distribution pipe to cylinder head 6 - 89
Wiring harness to valve cover 5 - 44
Generator power connection 10 - 89
Lower intake manifold retaining bolts a) - -
Upper intake manifold retaining bolts a) - -
Intake manifold runner control actuator retaining bolts 10 - 89
Electronic ignition (EI) coil retaining bolts 6 - 53
Ground cable to EI coil 6 - 53
Intermediate shaft bracket retaining bolts 47 35 -
Exhaust gas recirculation (EGR) pipe to EGR valve 40 30 -

a) Refer to the procedure in this section.

Mechanical Repairs > 3 Powertrain > 303 Engine > 303-01C Engine - 2.5L Duratec-VE (VE6) > Specifications

[PREV PAGE] [NEXT PAGE]