Workshop Manuals Factory service & repair GMC
01 Relays and Modules02 Sensors and Switches03 Maintenance04 Engine, Cooling and Exhaust05 Powertrain Management06 Transmission and Drivetrain07 Brakes and Traction Control08 Starting and Charging09 Power and Ground Distribution10 Steering and Suspension11 Heating and Air Conditioning12 Restraint Systems13 Accessories and Optional Equipment14 Body and Frame15 Cruise Control16 Instrument Panel, Gauges and Warning Indicators17 Lighting and Horns18 Windows and Glass19 Wiper and Washer Systems
GMC Suburban 1/2 Ton 2WD V8-305 5.0L (1986)03 · Maintenance
03 · Maintenance

Brakes - Pull/Lead When Braking (Alignment)

Make
GMC
Model
Suburban 1/2 Ton 2WD
Engine
V8-305 5.0L
Year
1986
Section
Jan › 89 › Brakes - Pull/Lead When Braking
MaintenanceBrakes - Pull/Lead When Braking · page 1 of 6
Brakes - Pull/Lead When Braking (Alignment) – GMC Suburban 1/2 Ton 2WD V8-305 5.0L (1986)

Technical Service Bulletin # 88T1845

Date: 890101

Brakes - Pull/Lead When Braking

GMC NUMBER:

88-T-184

GROUP:

5 - Brakes

DATE:

January, 1989

CORPORATE
NUMBER:

865006R

SUBJECT:

LEAD WHILE BRAKING

MODELS:

1984-86 K1-2 AND 1987-88 V1-2

A condition described as directional lead (either right or left) while braking may be addressed on the models listed above by careful inspection,
adjustment or repair of the vehicle's tires, suspension, steering or brake components. The following procedures have been developed to systematically
address the area(s) that should be inspected and adjusted. Evaluation of a vehicle's brake performance is not intended to be made with the vehicle
operator's hands removed from the steering wheel. Vehicles that exhibit directional bias under these conditions are not considered to exhibit brake lead.
Before road testing the vehicle, perform the following services:

NOTICE:

Follow the service procedures in the 1988 Light Duty Service Manual X-8832 unless noted differently.

Preliminary Inspection:

^

Inspect tires for excessive, uneven wear - replace if necessary.

^

Equalize tire pressures.

^

Torque leaf spring-to-axle U-bolts to high limit

of specification (150 ft.lbs. or 2 03 N-m). See Section 3C for tightening order.
^

Equalize parking brake adjustment.

^

Adjust rear service brakes to .030" running clearance.

^

Inspect and record front end alignment readings - adjust total toe to specifications (.0" to .14"). Inspect caliper brake line bolt (#34, page 5A8,
Figure 4, 1988 Service Manual X-8832) for mislocation of orifice. The orifice should be located in the unthreaded part of the bolt. If the orifice is
located in a threaded portion of the bolt, then the bolt must be replaced.

NOTICE:

After the preceding inspections and/or adjustments have been made, the vehicle should be road tested to determine if a lead still exists.
Vehicles that lead may lead either right or left when the brakes are applied.

Make all stops on a dry, level (no crown), clean roadway.

FIGURE 1 - CALIPER/KNUCKLE CLEARANCES

IMPORTANT!

EACH APPLICABLE STEP MUST BE THOROUGHLY COMPLETED TO EFFECT A LASTING REPAIR. FAILURE TO COMPLETE THE
PROCEDURE EXACTLY AS WRITTEN MAY RESULT IN AN UNSATISFACTORY REPAIR.

Pinch or Ctrl + scroll to zoom. Double-tap to reset.

Parts & tools for this job For 1986 GMC Suburban 1/2 Ton 5.0L

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.