Commander 4WD V6-3.7L VIN K (2007)
![background image](/jeep/commander_4wd/v6-3.7l_vin_k/Page-1091001.png)
Temperature Gauge: Description and Operation
Operation
OPERATION
The engine coolant temperature gauge gives an indication to the vehicle operator of the engine coolant temperature. This gauge is controlled by the
instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Powertrain Control Module
(PCM) over the Controller Area Network (CAN) data bus.
The engine coolant temperature gauge is driven by an electronic stepper motor unit that receives battery current on the instrument cluster electronic
circuit board through the fused ignition switch output (run-start) circuit whenever the ignition switch is in the ON or START positions. The cluster is
programmed to move the gauge needle back to the low end of the scale after the ignition switch is turned to the OFF position. The instrument cluster
circuitry controls the gauge needle position and provides the following features:
-
Engine Temperature Message - Each time the cluster receives an electronic engine temperature message from the PCM indicating the
temperature is between the low end of normal [about 41° C (105° F) for gasoline engines, or about 28° C (82° F) for diesel engines] and the
high end of normal [about 124° C (255° F) for gasoline engines, or about 124° C (256° F) for diesel engines], the gauge needle is moved to the
actual relative temperature position on the gauge scale.
-
Engine Temperature Low Message - Each time the cluster receives an electronic engine temperature message from the PCM indicating the
temperature is low [at or below about 40° C (104° F) for gasoline engines, or about 27° C (81° F) for diesel engines], the gauge needle is held
below the graduation on the far left end of the gauge scale. The gauge needle remains below the low end of the gauge scale until the cluster
receives a message from the PCM indicating that the temperature is above the low end of normal, or until the ignition switch is turned to the OFF
position, whichever occurs first.
-
Engine Temperature High Message - Each time the cluster receives an electronic engine temperature message from the PCM indicating the
temperature is high [at or above about 127° C (261° F) for gasoline engines, or about 128° C (262° F) for diesel engines], the gauge needle is
moved to the zone between the two red graduations at the high end of the gauge scale, a check gauges indicator textual warning is displayed in the
reconfigurable dot matrix display, and a single chime tone is sounded. The gauge needle remains between the red graduations and the check
gauges indicator textual warning remains illuminated until the cluster receives a message from the PCM indicating that the temperature is below
about 124° C (255° F) or above the critical threshold, or until the ignition switch is turned to the OFF position, whichever occurs first. The chime
tone feature will only repeat during the same ignition cycle if the check gauges indicator is cycled OFF and then ON again by the appropriate
messages from the PCM.
-
Engine Temperature Critical Message - Each time the cluster receives an electronic engine temperature message from the PCM indicating the
temperature is critical [above about 132° C (270° F)], the gauge needle is held at the red H graduation at the high end of the gauge scale and a
check gauges indicator textual warning is displayed in the reconfigurable dot matrix display. The gauge needle remains at the red H graduation
until the cluster receives a message from the PCM indicating that the temperature is below critical [about 127° C (26° F)], or until the ignition
switch is turned to the OFF position, whichever occurs first.
-
Communication Error - If the cluster fails to receive an engine temperature message, it will hold the gauge needle at the last indication for
about five seconds or until the ignition switch is turned to the OFF position, whichever occurs first. After five seconds, the cluster will move the
gauge needle to the low end of the gauge scale.
-
Actuator Test - Each time the cluster is put through the actuator test, the engine coolant temperature gauge needle will be swept to several
calibration points on the gauge scale in a prescribed sequence in order to confirm the functionality of the gauge and the cluster control circuitry.
The PCM continually monitors the engine coolant temperature sensor to determine the engine operating temperature. The PCM then sends the proper
messages to the ElectroMechanical Instrument Cluster (EMIC). If the instrument cluster turns ON the check gauges indicator due to a high or critical
engine temperature gauge reading, it may indicate that the engine or the engine cooling system requires service.
For proper diagnosis of the engine coolant temperature sensor, the PCM, the EMIC, the CAN data bus or the electronic communication related to engine
coolant temperature gauge operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.