landrover Workshop Repair Guides

Land Rover Workshop Service and Repair Manuals

Diagram Information and Instructions|Page 9034 > < Diagram Information and Instructions|Page 9032
Page 2
background image

-

To the LH headlamp dipped beam bulb (C0009) on a WG wire.

Both are earthed on N wires.

Headlamp Main Beam

In addition to the lamps outlined in the side lamps and headlamp dipped beam sections, the LCM will provide feeds to the following lamps if it detects
that headlamp main beam has been selected:

-

To the RH headlamp main beam bulb (C0011) on a WU wire

-

To the LH headlamp main beam bulb (C0009) on a YG wire.

Both are earthed on N wires.

Bi-Xenon System

Power Distribution

Feed from the positive battery terminal (C0192) is supplied to fuse 53, fusible link 3, and fusible link 4 on an R wire. All are located in the passenger
compartment fuse box. Fusible link 3 (C0589) and fusible link 4 (C0590) provide constant battery feeds to the Light Check Module (LCM) (C0937 R
C2039 respectively) on a pair of R wires. The LCM (C2039) is
earthed on an N wire.

Fuse 53 (C0583) provides a constant battery feed to the ignition switch (C0028 on V8 vehicles) on an R wire. When the ignition switch is turned to the
'auxiliary' position, current flows across the switch (C0028 on V8 vehicles) to fuse 9 of the passenger compartment fuse box (C0585) on a PB wire. Fuse
9 (C0587) provides an auxiliary ignition feed to the LCM (C2040) on a PY wire.

When the ignition switch is turned to the 'ignition' position, current flows across the switch (C0028 on V8 vehicles) to fuse 4 and fuse 32 of the
passenger compartment fuse box (C0585) on a G wire. Fuse 4 (C0587) provides an ignition feed to the LCM (C2040) on a GS wire.

Fuse 32 of the passenger compartment fuse box (C0585) provides an ignition feed to LH bi-xenon headlamp (C0009) on a GR wire. Fuse 32 (C0587)
also provides an ignition feed to the RH bi-xenon headlamp (C0011) on a GR wire.

Light Check Module

The LCM (C2040) is located at the base of the RH 'A' post, and monitors the condition of the fascia mounted rotary lighting switch (C0041) by
providing a feed on an NB wire. The LCM can determine the position of the switch by sensing if a feed is returned on a Y (side lamps) or a B
(headlamps) wire. The LCM also monitors the condition of the column mounted main/dipped beam switch (C1832) via a U wire.

Side Lamps

If the LCM detects that side lamps have been selected, it provides a feed to the following:

-

To the RH side lamp (C0537) on an SU wire

-

To the LH side lamp (C0538) on an SG wire

-

To the RH tail lamp (C0125) on an SW wire

-

To the LH tail lamp (C0121) on an SP wire

-

The rear number plate lamp (C1495) on an SN and an SB wire

-

To the RH front side marker lamp (C0916) on an SU wire (NAS vehicles only)

-

To the RH rear side marker lamp (C0918) on an SU wire (NAS vehicles only)

-

To the LH front side marker lamp (C0917) on an SG wire (NAS vehicles only)

-

To the LH rear side marker lamp (C0919) on an SG wire (NAS vehicles only).

All are earthed on N wires.

Headlamp Dipped Beam

In addition to the lamps outlined in the side lamps section, the LCM will provide feeds to the following lamps if it detects that headlamp dipped beam
has been selected:

-

To the RH headlamp dipped beam bulb (C0011) on a YU wire

-

To the LH headlamp dipped beam bulb (C0009) on a WG wire.

Both are earthed on N wires.

Headlamp Main Beam

In addition to the lamps outlined in the side lamps and headlamp dipped beam sections, the LCM will provide feeds to the following lamps if it detects
that headlamp main beam has been selected:

Diagram Information and Instructions|Page 9034 > < Diagram Information and Instructions|Page 9032