Workshop Manuals Factory service & repair Mercedes Benz
01 Relays and Modules02 Sensors and Switches03 Maintenance04 Engine, Cooling and Exhaust05 Powertrain Management06 Transmission and Drivetrain07 Brakes and Traction Control08 Starting and Charging09 Power and Ground Distribution10 Steering and Suspension11 Heating and Air Conditioning12 Restraint Systems13 Accessories and Optional Equipment14 Body and Frame15 Cruise Control16 Instrument Panel, Gauges and Warning Indicators17 Lighting and Horns18 Windows and Glass19 Wiper and Washer Systems
Mercedes Benz SLK 280 (171.454) V6-3.0L (272.942) (2007)04 · Engine, Cooling and Exhaust
04 · Engine

Engine - MIL ON/Multiple Camshaft Codes Set (Variable Valve Timing Actuator)

Make
Mercedes Benz
Model
SLK Class SLK 280 (171.454)
Engine
V6-3.0L (272.942)
Year
2007
Section
Oct › 08 › Engine - MIL ON/Multiple Camshaft Codes Set
Engine, Cooling and ExhaustEngine - MIL ON/Multiple Camshaft Codes Set · page 1 of 7
Engine - MIL ON/Multiple Camshaft Codes Set (Variable Valve Timing Actuator) – Mercedes-Benz SLK 280 R171 V6-3.0L M272 (2007)

Variable Valve Timing Actuator: All Technical Service Bulletins
Engine - MIL ON/Multiple Camshaft Codes Set

DTB

Date: 

October 24, 2008

Order No.: 

S-B-03.30/08h

Supersedes: 

S-B-03.30/08g dated October 20, 2008

Group: 

03

SUBJECT: Model 164.172/186/871/886

Model 171.454/456
Model 203.052/054/056/087/092
Model 204.054/056/081
Model 209.356/372/456/472
Model 211.056/072/087/090/256/287
Model 216.371
Model 219.372
Model 221.171/186
Model 230.471
Model 251.156/165
Equipped with M272 or M273 Engine
Check Engine Light On / Fault Codes 0059, 0060, 0063, 0064, 0271, 0272, 0275, 0276, 1200 and/or 1208 Stored in ME-SFI Control
Module / Camshaft Adjustment Solenoid Leaking Oil

If you receive customer reports of the check engine light being illuminated and the following fault code scenario is found in the above model vehicles,
follow the applicable procedure below to resolve.

Fault Code Scenario 1: DTC 1200 and/or 1208 are stored in ME-SFI control module. The fault codes are recorded as current and stored in the fault
memory. When the fault memory is erased and the engine is restarted, the fault codes reoccur immediately. This is due to the positioning of the camshafts
of the right cylinder bank relative to the crankshaft being impaired by a worn sprocket on the balance shaft on engine M272 or by a worn guide (idler)
gear for the timing chain on engine M273.

Applicable Models (Not Applicable to Model 204): Equipped with M272 Engine Up to Serial No. 2729..30 468993 or M273 Engine Up to Serial No.
2739..30 088611

Procedure 1:

a. Perform a visual inspection for wear of teeth on sprocket of balance shaft (M272) or of guide (idler) gear for timing chain (M273) by removing the

timing case cover on the engine.

NOTE:  When inspecting the component, refer to Figure 1 for an example of a damaged gear.

Pinch or Ctrl + scroll to zoom. Double-tap to reset.

Parts & tools for this job For 2007 Mercedes-Benz SLK Class 3.0L

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.