Aurora V6-214 3.5L VIN H SFI (2001)
Body Control Module: Procedures
Body Control Module Programming/RPO Configuration (DIM)
IMPORTANT: The Air Bag Indicator light may remain ON after the DIM Module is replaced and during the programming procedure for the DIM
until after the procedure is completed and the ignition key is cycled OFF and ON.
1. Before replacement record the personalization settings to transfer to the new module (if they are available). Refer to Personalization Description
and Operation in Personalization.
2. After replacement or to reprogram the DIM perform the following procedure.
1. Ensure the scan tool has been updated with the latest software version.
2. Connect a scan tool to the data link connector (DLC).
3. Turn ON the ignition, with the engine OFF.
4. Under the DIM Main Menu, select Special Functions. Under the Special Functions menu, one of the choices is New VIN.
5. The user selects one of the following:
^
New VIN, (to continue with the procedure).
^
Exit, to go back to Special Functions menu.
6. After the user chooses New VIN, follow the scan tool on screen instructions to edit VIN:
^
Press Save to save VIN information.
^
Press Done to go back to Special Functions menu.
7. Under the Special Functions menu, one of the choices is Setup SDM Serial Number in DIM.
8. The user selects one of the following:
^
Setup SDM Serial Number in DIM, (to continue with the procedure).
^
Exit, to go back to Special Functions menu.
9. After the user chooses Setup SDM Serial Number in DIM, the scan tool displays a screen as follows:
^
Do you want to set up a Dash Integration Module?
^
Press Yes to set up module.
^
Press No to Exit.
10. Choose Yes or No
^
If the user selects No, the scan tool display returns to the DIM Special Function Menu.
^
If the user selects Yes, the scan tool displays Initializing New Module.
11. Once complete, the scan tool displays Module Initialized.
12. To complete the procedure, select the following:
13. EXIT: Go to Special Functions Menu
14. The user selects one of the following:
^
Set Options, (to continue with the procedure).
^
Exit, to go back to Special Functions menu.
15. Under the Set Options menu, the user selects from the following as available:
^
Automatic/Manual HVAC Options, (to continue with the procedure) follow the scan tool on screen instructions to Select the RPO option
configuration.
^
Headlamp Type Option, (to continue with the procedure) follow the scan tool on screen instructions to Select the Headlamp Type option
configuration.
^
LH Driver. Personalization, (to continue with the procedure) follow the scan tool on screen instructions to Select the LH Driver
Personalization option configuration.
^
Magna Steer Option, (to continue with the procedure) follow the scan tool on screen instructions to Select the RPO option configuration.
^
Miscellaneous Options #1, (to continue with the procedure) follow the scan tool on screen instructions to Select the RPO option
configuration.
^
Miscellaneous Options #2, should be turned ON.
^
Personalization Option, (to continue with the procedure) follow the scan tool on screen instructions to Select the RPO option configuration.
^
Point of Sale, (to continue with the procedure) follow the scan tool on screen instructions to Select the Point of Sale.
^
RH Driver. Personalization, (to continue with the procedure) follow the scan tool on screen instructions to Select the RH Driver
Personalization option configuration.
^
Right Hand Drive, (to continue with the procedure) follow the scan tool on screen instructions to Select Right Hand Drive option
configuration.
^
Universal Theft Deterrent, (to continue with the procedure) follow the scan tool on screen instructions to Select the RPO option
configuration.
^
Exit, to go back to Special Functions menu.
16. Perform the vehicle personalization to reset the owner's desired personalization settings. Refer to Personalization Description and Operation
in Personalization.
17. Cycle the ignition key OFF and ON.
Body Control Module Programming/RPO Configuration (IPM)
Ensure the scan tool has been updated with the latest software version.
The following steps should be followed to perform the recalibration update.