G6 V6-3.9L (2009)
1. Install the servo spring.
2. Install the piston assembly.
3. Install the O-ring.
4. Install the servo cover.
Caution: Refer to Fastener Caution (See: Service Precautions/Vehicle Damage Warnings/Fastener Caution).
5. Install the forward servo cover bolts.
Tighten the bolts to 12 Nm (106 lb in).
6. Remove the drain pan from under the forward servo cover.
7. Adjust the jackstand to raise the rear of the frame.
8. Install the frame bolts. Refer to Frame Replacement (Convertible) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and
Repair/Frame Replacement (Convertible))Frame Replacement (Coupe 2.4L) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and
Repair/Frame Replacement)Frame Replacement (3.6L) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and Repair/Frame
Replacement)Frame Replacement (Coupe 3.5L, 3.9L) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and Repair/Frame
Replacement).
9. Remove the support from the rear of the frame.
10. Install the power steering lines to the right side of the frame.
11. Install the engine mount lower nuts. Refer to Engine Mount Replacement (Coupe) (See: Engine, Cooling and Exhaust/Engine/Drive Belts,
Mounts, Brackets and Accessories/Engine Mount/Service and Repair)Engine Mount Replacement (Convertible) (See: Engine, Cooling and
Exhaust/Engine/Drive Belts, Mounts, Brackets and Accessories/Engine Mount/Service and Repair).
12. Install the rear transaxle mount bracket lower nuts. Refer to Transmission Rear Mount Bracket Replacement (See: Transmission Mount/Service
and Repair/4T65-E - Automatic Transmission/Transmission Rear Mount Bracket Replacement).
13. Install the transaxle mount lower nuts. Refer to Transmission Mount Replacement - Left Side (Sedan/Coupe) (See: Transmission Mount/Service
and Repair/4T65-E - Automatic Transmission/Transmission Mount Replacement - Left Side (Sedan/Coupe))Transmission Mount Replacement -
Left Side (Convertible) (See: Transmission Mount/Service and Repair/4T65-E - Automatic Transmission/Transmission Mount Replacement -
Left Side (Convertible)).
Note: It is recommended that the transmission adaptive pressure (TAP) information be reset. Resetting the TAP values using a scan tool will erase
all learned values in all cells. As a result, the engine control module (ECM), powertrain control module (PCM) or transmission control module
(TCM) will need to relearn the TAP values. Transmission performance may be affected as new TAP values are learned. Reset the TAP values.
Refer to Transmission Adaptive Functions (See: Description and Operation/4T65-E - Automatic Transmission/Transmission Adaptive Functions
).
14. Install the power steering gear. Refer to Steering Gear Replacement (Electronic Power Steering) (See: Steering and Suspension/Steering/Steering
Gear/Service and Repair)Steering Gear Replacement (Hydraulic Power Steering LY7) (See: Steering and Suspension/Steering/Steering
Gear/Service and Repair)Steering Gear Replacement (Hydraulic Power Steering LZ4, LZ9) (See: Steering and Suspension/Steering/Steering
Gear/Service and Repair).
15. Lower the vehicle.
16. Remove the engine support fixture.
17. Check and fill the transaxle as necessary.
Reverse Servo Replacement
Reverse Servo Replacement
Removal Procedure
1. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement (See: Engine, Cooling and Exhaust/Engine/Tune-up and
Engine Performance Checks/Air Cleaner Housing/Air Cleaner Fresh Air Duct/Hose/Service and Repair/Air Cleaner Outlet Duct Replacement).
