Leon Mk1
Assembly overview: Transverse link, track rod (all-wheel drive) |
-Arrow- points in direction of normal travel. |
1 - | Eccentric bolt |
q | After slackening off, perform wheel alignment → Chapter |
q | Do not turn more than 90° in either direction (i.e. from minimum to maximum adjustment position) |
2 - | Nut |
q | M12 x 1.5 |
q | 95 Nm |
q | Self-locking |
q | Can be loosened and tightened up to 5 times for adjustment work. |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
3 - | Eccentric washer |
q | Inner hole with lug |
4 - | Eccentric bolt |
q | After slackening off, perform wheel alignment → Chapter |
q | Do not turn more than 90° in either direction (i.e. from minimum to maximum adjustment position) |
Note
The eccentric bolt can also be installed facing the rear. |
5 - | Eccentric washer |
q | Inner hole with lug |
6 - | Nut |
q | M12 x 1.5 |
q | 95 Nm |
q | Self-locking |
q | Can be loosened and tightened up to 5 times for adjustment work. |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
Note
t | To tighten nuts, set torque wrench -V.A.G 1332- to 80 Nm. |
t | This torque setting only applies in conjunction with 18 mm tool insert -T10179-. |
7 - | Sub-frame |
q | Repairs → Chapter |
8 - | Bolt. |
q | M12 x 1.5 x 125 |
q | 90 Nm and then turn 90° further |
q | Always renew if removed |
9 - | Lower transverse arm |
q | removing and installing → Chapter |
10 - | Nut |
q | 90 Nm and then turn 90° further |
q | Self-locking |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
11 - | Bolt. |
q | M12 x 1.5 x 75 |
q | Always renew if removed |
12 - | Threaded rivet |
q | M6 |
13 - | Expanding rivet |
14 - | Stone deflector |
15 - | Hexagonal bolt |
q | M6 x 12 |
q | 8 Nm |
16 - | Nut |
q | Self-locking |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
17 - | Washer |
18 - | Bolt. |
q | M14 x 1.5 x 115 |
q | 130 Nm and then turn 90° further |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
19 - | Washer |
20 - | Lower transverse swinging arm |
q | removing and installing → Chapter |
21 - | Washer |
22 - | Nut |
q | Self-locking |
q | Always renew if removed |
23 - | Wheel bearing housing |
q | removing and installing → Chapter |
24 - | Washer |
25 - | Bolt. |
q | M14 x 1.5 x 115 |
q | 130 Nm and then turn 90° further |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
26 - | Track rod |
q | Forwards closed (left and right track rods differ) |
q | removing and installing → Chapter |
27 - | Bolt. |
q | M12 x 1.5 x 125 |
q | 90 Nm and then turn 90° further |
q | Always renew if removed |
28 - | Bolt. |
q | M12 x 1.5 x 95 |
q | Always renew if removed |
q | Always tighten bolted joints with suspension in unladen position → Chapter |
29 - | Nut |
q | 90 Nm and then turn 90° further |
q | Self-locking |
q | Always renew if removed |