SEAT Workshop Service and Repair Manuals

• Activated charcoal filter
• ◆ Location: in front right wheel housing
• ◆ Remove wheel housing liner to remove
• ◆ Activated charcoal filter system

=> Repair group 20; Activated charcoal filter system

• Air cleaner
• ◆ Dismantling and assembling
• Activated charcoal filter solenoid valve 1 (N80)
• ◆ Activated charcoal filter system

=> Repair group 20; Activated charcoal filter system

• Knock sensor 1 (G61)
• ◆ Fitting location: Cylinder block exhaust side
• ◆ => Page 28-5, item 15
• Air mass meter (G70) with intake air temperature sender (G42)
• Throttle valve control part (J338)
• ◆ Heated by coolant
• Fuel pressure regulator
• Combi-valve
• ◆ Secondary air system:

=> Repair group 26; Secondary air system; Removing and installing parts of secondary air system

• Lambda probe 1 bank 1 before catalyst (G39), 50Nm
• ◆ Location: in catalyst, front

• 6-pin connector
• ◆ Black
• ◆ Contacts gold plated
• ◆ For Lambda probe 1 before catalyst (G39) and Lambda probe heater (Z19)
• ◆ Left on underside of vehicle
• Lambda probe 2 bank 1 after catalyst (G130), 50Nm
• ◆ Location: Behind catalyst
• 4-pin connector
• ◆ Black
• ◆ Contacts 3 and 4 gold-plated
• ◆ For Lambda probe 2 after catalyst (G130) and Lambda probe heating (Z29)
• ◆ Left on underside of vehicle
• Clutch pedal switch (F36), brake light switch (F) and brake pedal switch (F47)
• ◆ Location: in left footwell

• Secondary air pump relay (J299)*
• ◆ Location: on lower relay carrier behind multi-function unit -relay position 22-
• Engine control unit
• (Motronic control unit -J220)
• Connector
• ◆ For engine control unit
• ◆ Only disconnect or connect with ignition switched off
• ◆ Release to disconnect
• Hall sender (G163)
• ◆ for exhaust camshaft
• ◆ => Page 28-4, item 11
• ◆ Mark connector before pulling off

• Exhaust camshaft control valve 1 (N318)
• ◆ for exhaust camshaft
• ◆ Mark connector before pulling off
• Camshaft adjustment valve 1 (N205)
• ◆ For intake camshaft
• ◆ Mark connector before pulling off
• Hall sender (G40)
• ◆ For intake camshaft
• ◆ => Page 28-5, item 14
• ◆ Mark connector before pulling off
• Protective housing
• ◆ For additional protection

• Vacuum positioning element
• ◆ For intake manifold change-over
• Coolant temperature sender (G62)
• ◆ For engine control unit
• ◆ Black, 2-pin
• ◆ If necessary release pressure in cooling system before removing
• Engine speed sender (G28)
• Knock sensor 2 (G66)
• ◆ Fitting location: Cylinder block intake side
• ◆ => Page 28-5, item 15
• Intake manifold change-over valve (N156)
• ◆ Mark connector before pulling off

• Secondary air inlet valve (N112)
• ◆ Mark connector before pulling off
• ◆ Secondary air system:

=> Repair group 26; Secondary air system; Removing and installing parts of secondary air system

• Secondary air pump motor (V101)
• ◆ Secondary air system:

=> Repair group 26; Secondary air system; Removing and installing parts of secondary air system

• Ignition coil with output stage (N70, N127, N291, N292, N323 and N324)
• ◆ => Page 28-2, item 1
• Injector (N30...N33, N83, N84)