Test
|
Work Order Description
|
Nominal Value
|
T001
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Reconnect all disconnected components
- All consumers turned off
- Insert new component:
FE26 Fuse
|
Test okay?
|
|
T002
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 12 XEP Z 14 XEP Z 14 XEL
|
|
|
T003
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Insert new fuse FE26 and then check the fuse for proper operation.
- Ignition ON
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B57 Sensor - Oxygen, Catalytic Converter Check B166 Sensor - Oxygen, Mixture Control, Heated Y56 Solenoid Valve - Exhaust Gas Recirculation Y21C Solenoid Valve - Twinport
|
Test okay?
|
|
T004
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 18 XE
|
|
|
T005
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Insert new fuse FE26 and then check the fuse for proper operation.
- Ignition ON
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B69 Air Mass Meter B166 Sensor - Oxygen, Mixture Control, Heated B57 Sensor - Oxygen, Catalytic Converter Check
|
Test okay?
|
|
T006
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 XEP Z 16 XE1
|
|
|
T007
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B57 Sensor - Oxygen, Catalytic Converter Check B166 Sensor - Oxygen, Mixture Control, Heated Y158 Thermostat, Map-Controlled Y56 Solenoid Valve - Exhaust Gas Recirculation Y1_Y21B Solenoid Valve - Twinport
|
Test okay?
|
|
T008
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 17 DTH Z 17 DTL
|
|
|
T009
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y145 Solenoid Valve - Swirl
- Insert new fuse FE26 and then check the fuse for proper operation.
- Ignition ON
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
Y56 Solenoid Valve - Exhaust Gas Recirculation
|
Test okay?
|
|
T010
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 18 XER
|
|
|
T011
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B69 Air Mass Meter B57 Sensor - Oxygen, Catalytic Converter Check B166 Sensor - Oxygen, Mixture Control, Heated Y21 Solenoid Valve - Intake Manifold Y164 Solenoid valve - Camshaft, intake Y162 Solenoid valve - Camshaft, exhaust Y158 Thermostat, Map-Controlled
Note:
During model year 2008 the following changes occur:
The component B69 is no longer installed
|
Test okay?
|
|
T012
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 20 LEL Z 20 LER Z 20 LEH Z 16 LET A 16 LET
|
|
|
T013
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B166 Sensor - Oxygen, Mixture Control, Heated B57 Sensor - Oxygen, Catalytic Converter Check
|
Test okay?
|
|
T014
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 19 DTH Z 19 DT Z 19 DTL
|
|
|
T017
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Diesel Particulate Filter
|
|
|
T018
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B56 Sensor - Oxygen, Exhaust, Heated
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
|
Test okay?
|
|
T020
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine (Wiring Harness Connector XC53 )
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
|
Test okay?
|
|
T021
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 13 DTH
|
|
|
T022
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y142 Solenoid Valve - Boost Pressure Regulation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
Y56 Solenoid Valve - Exhaust Gas Recirculation Y38 Solenoid Valve - Intake Air Throttle A84 Control Unit - Engine (Wiring Harness Connector XC19 )
|
Test okay?
|
|
T023
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 XER
|
|
|
T024
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B57 Sensor - Oxygen, Catalytic Converter Check B166 Sensor - Oxygen, Mixture Control, Heated Y164 Solenoid valve - Camshaft, intake Y162 Solenoid valve - Camshaft, exhaust Y158 Thermostat, Map-Controlled Y21 Solenoid Valve - Intake Manifold
|
Test okay?
|
|
T025
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 22 YH
|
|
|
T026
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y123 Solenoid Valve - Tank Ventilation
- Ignition ON
- Insert new fuse FE26 and then check the fuse for proper operation.
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
B69 Air Mass Meter B28 Sensor - Camshaft B166 Sensor - Oxygen, Mixture Control, Heated B57 Sensor - Oxygen, Catalytic Converter Check
|
Test okay?
|
|