Astra J
DTC B3205, B3210, B3215, or B3220Diagnostic Instructions
DTC DescriptorsDTC B3205 00: Driver Window Motor CircuitDTC B3205 39: Driver Window Motor Circuit Internal Malfunction DTC B3205 42: Driver Window Motor Circuit Calibration Not Programmed DTC B3205 4B: Driver Window Motor Circuit Calibration Not Learned DTC B3210 00: Right Front Window Motor Circuit DTC B3210 39: Right Front Window Motor Circuit Internal Malfunction DTC B3210 42: Right Front Window Motor Circuit Calibration Not Programmed DTC B3210 4B: Right Front Window Motor Circuit Calibration Not Learned DTC B3215 00: Left Rear Window Motor Circuit DTC B3215 39: Left Rear Window Motor Circuit Internal Malfunction DTC B3215 42: Left Rear Window Motor Circuit Calibration Not Programmed DTC B3215 4B: Left Rear Window Motor Circuit Calibration Not Learned DTC B3220 00: Right Rear Window Motor Circuit DTC B3220 39: Right Rear Window Motor Circuit Internal Malfunction DTC B3220 42: Right Rear Window Motor Circuit Calibration Not Programmed DTC B3220 4B: Right Rear Window Motor Circuit Calibration Not Learned Circuit/System DescriptionThe body control module (BCM) monitors, receives and transmits serial data to each of the doors switches and window motors. When a window switch has been activated on the driver window switch, a signal is sent to the BCM which sends a signal to the appropriate window motor and the window motor will move in the direction commanded. Conditions for Running the DTC
Conditions for Setting the DTCB3205 00, B3210 00, B3215 00, B3220 00The BCM has detected that the compatibility code stored in the affected window motor does not match the compatibility code stored in the BCM. B3205 39, B3210 39, B3215 39, B3220 39An internal malfunction has been detected by the BCM in the power window motor while commanding the window UP or DOWN. B3205 42, B3210 42, B3215 42, B3220 42The BCM will automatically attempt to download the calibration program into the appropriate window motor (As will occur when the window motor has been replaced), if the first calibration program fails to load, the BCM will attempt to download the calibration program a second time. If this download fails, the BCM will set appropriate DTC. B3205 4B, B3210 4B, B3215 4B, B3220 4BThe BCM detects that a window motor is "not normalized" which will occur under the following conditions:
Action Taken When the DTC SetsB3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39The affected motor will be inoperative. B3205 4B, B3210 4B, B3215 4B, B3220 4BThe affected motor will not perform the express up or express down functions and the driver information center will display Open, then Close Driver Window or will display Open, then Close Passenger Window. Conditions for Clearing the DTCB3205 00, B3210 00, B3215 00, B3220 00Installing a compatible window motor for that specific make and model vehicle. B3205 39, B3210 39, B3215 39, B3220 39The appropriate window motor must be replaced before the DTC can be cleared. B3205 42, B3210 42, B3215 42, B3220 42The appropriate window motor must be replaced before the DTC can be cleared. B3205 4B, B3210 4B, B3215 4B, B3220 4BThe appropriate window motor must be normalized before the DTC can be cleared. Reference InformationSchematic ReferenceConnector End View ReferenceDescription and OperationPower Windows Description and Operation Electrical Information ReferenceScan Tool ReferenceControl Module References for scan tool information Circuit/System VerificationB3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 00, B3215 39, B3215 42, B3220 00, B3220 39, B3220 42
Note: If the window performs the UP and DOWN functions, clear the DTC Circuit/System TestingB3205 4B, B3210 4B, B3215 4B, B3220 4B
Note: The doors must be completely closed prior to normalizing the windows, a door that is open or ajar may cause the power window to function abnormally or it may become inoperative while performing the normalization procedure. If this occurs, verify that the door is completely closed then repeat the normalization procedure. If the M74 Window Motor does not perform as specified and the DTC resets, replace the M74 Window Motor. Repair InstructionsPerform the Diagnostic Repair Verification after completing the diagnostic procedure.
|
||||||||||||||||||||