|
Special tools - R 25/R 28/R 30
|
KM-113-2
|
Bracket
|
|
To fasten bracket to workbench
|
|
KM-237
|
Guide Bolt
|
|
To centre the clutch plate
|
|
KM-238-B
|
Height Gauge
|
|
To measure axial play of gear cluster in conjunction with
KM-713
|
|
KM-302
|
Installer Sleeve
|
|
To drive roller bushing into transmission housing in conjunction
with KM-370
|
|
KM-307-B
|
Remover Plate
|
|
To remove synchromesh body and gears from main shaft
|
|
|
|
KM-308
|
Remover / Installer
|
|
To install spiral pins of shift rod and shift lever shafts
|
|
KM-328-B
|
Remover
|
|
To remove shifting lock plugs in conjunction with KM-630
|
|
KM-370
|
Installer 1)
|
|
To drive roller bushing into transmission housing in conjunction
with KM-302
|
|
KM-409-A
|
Remover / Installer 1)
|
|
To install shift rod bushing in transmission housing
|
|
KM-454-B
|
Remover / Installer
|
|
To install auxiliary shaft gear cluster roller bearing. Can be
used instead of KM-302 and KM-370
|
|
KM-461-C
|
Installer
|
|
To install main drive gear ball bearing
|
|
|
|
KM-526-A
|
Clamp Set
|
|
To compress clutch assembly (in OHC petrol engine with flange
flywheel)
|
|
KM-556-A
|
Puller Set
|
|
To remove roller bearing from transmission housing nose piece in
conjunction with Kukko 21/2
|
|
KM-622-A
|
Transmission Holder
|
|
To hold transmission along with KM-113-2
|
|
KM-623
|
Holding Wrench
|
|
To hold transmission flange when loosening and tightening
fastening nuts
|
|
KM-627
|
Ring Pliers
|
|
To remove and install bearing retaining ring on transmission
housing nose piece
|
|
KM-628-A
|
Remover
|
|
To remove transmission flange and front section of transmission
housing from main drive gear bearing and from transmission housing
nose piece
|
|
|
|
KM-629-A
|
Ring Installer
|
|
To install seal rings in transmission housing nose piece and
thrust bearing guide sleeve
|
|
KM-630
|
Remover
|
|
To remove shift lock plugs in conjunction with KM-328-B
|
|
KM-631-A
|
Adjuster
|
|
To adjust selector lever on 5-speed manual transmission R 25 and
R 28
|
|
KM-632-A
|
Remover / Installer
|
|
To remove and install clutches on OHC petrol engines with flat
flywheel
|
|
KM-652
|
Flywheel Holder
|
|
To remove and install clutch thrust plate, replacement for
KM-139-A
|
|
KM-713
|
Adjuster
|
|
To measure the axial play of auxiliary shaft gear cluster. In
conjunction with KM-238-B
|
|
|
|
MKM-6174-A
|
Bleeding Device
|
|
Bleeding clutch actuation in conjunction with brake bleeder
|
|
KM-6263
|
Remover / Installer
|
|
Securing overall clutch, removing clutch, centring clutch disks
for installation
|
|
KM-6289
|
Resetting tool
|
|
Resetting SAC clutch adjusting ring
|
|
|
1 ) no longer available
|
