volkswagen Workshop Repair Guides

Volkswagen Workshop Service and Repair Manuals

Test table for vehicles up to > 09.99 (with 45-pin control unit connector) > < Gearbox: Electrical check
Automatic gearbox 001 self-diagnosis
Gearbox: Electrical check
Electrical check for vehicles up to > 09.99 (with 45-pin control unit connector)

Control unit -J217- multi-pin connector (45 pin) assignment (sockets on V.A.G 1598/18)

1-

Earth (terminal 31)

20-

Kickdown switch -F8-

2-

Series resistance for solenoid valve -N207-

21-

Brake light switch -F- signal voltage

3-

Solenoid valve 6 voltage supply -N93-

22-

Fault memory supply voltage (terminal 30)

4-

Vacant

23-

Supply voltage (terminal 15)

5-

K-wire for diagnosis

24-

Earth (terminal 31)

6-

Selector lever lock solenoid -N110-

25-

Solenoid valve 4 -N91-

7-

Solenoid valve 1 -N88-

26-

Solenoid valve 3 -N90-

8-

Solenoid valve 2 -N89-

27-

Ignition timing point influence

9-

Gearbox speed sensor -G38-

28-

Vacant

10-

Gearbox speed sensor -G38-

29-

Vacant

11-

Gearbox speed sensor -G38- (screening)

30-

Vacant

12-

Vacant

31-

Vacant

13-

TD signal (rpm)

32-

Vacant

14-

Throttle valve potentiometer -G69- signal1)

33-

Gearbox oil temperature sender -G93- (ATF)

15-

Vacant

34-

Gearbox oil temperature sender -G93- (ATF)

16-

Vacant

35-

Road speed sender -G68-

17-

Vacant

36-

Road speed sender -G68-

18-

Multifunction switch -F125- (position "1")

37-

Road speed sender -G68- (screening)

19-

Multifunction switch -F125- (position "2")

38-

Vacant

1)     Signal (contact 14) directed via engine control unit to gearbox control unit and can only be checked in "Reading measured value block" .

39-

Vacant

40-

Multifunction switch -F125- (position "R")

41-

Multifunction switch -F125- (position "N")

42-

Multifunction switch -F125- (position "P")

43-

Multifunction switch -F125- (position "3")

44-

Multifunction switch -F125- (position "D")

45-

Supply voltage (terminal 15)

46 to 68 vacant

Test step overview

    Only perform test steps for the relevant component as listed in fault finding table and measured value block.

Component checked

Component checked

Voltage supply from control unit -J217-

- Perform test step 1

Solenoid valve 3 -N90-

- Perform test step 10

Selector lever lock solenoid -N110-

- Perform test step 2

Solenoid valve 4 -N91-

- Perform test step 11

Brake light switch -F-

- Perform test step 3

Solenoid valve 6 -N93-

- Perform test step 12

Multifunction switch -F125-

- Perform test step 4

Series resistance -N207-

- Perform test step 13

Kickdown switch -F8-

- Perform test step 5

Gearbox oil temperature sender -G93-

- Perform test step 14

Road speed sender -G68-

- Perform test step 6

Gearbox speed sender
-G38-

- Perform test step 7

Solenoid valve 1 -N88-

- Perform test step 8

Solenoid valve 2 -N89-

- Perform test step 9

Test table for vehicles up to > 09.99 (with 45-pin control unit connector) > < Gearbox: Electrical check