Audi Workshop Service and Repair Manuals

Special tools and workshop equipment required

• ◆ V.A.G 1526 A
• ◆ V.A.G 1594 A
• ◆ V.A.G 1598/31
• ◆ VAS 5051 with VAS 5051/1

• or

• ◆ V.A.G 1551 with V.A.G 1551/3 A

The fuel pump and certain components of the injection system are supplied with power by way of the fuel pump relay -J17.

The fuel pump relay -J17 is only energised when the engine is running, i.e. the relay is only connected to earth (via the engine control unit) when engine speed pulses are detected in the engine control unit.

Note:

→ The fuel pump relay is located in the central electric's, on the left in the driver's footwell, position 4.

Test requirements:

• ● Battery voltage at least 12.7 V

Functional check of fuel pump relay

• ‒ Remove driver's storage compartment.

=> General Body Assembly - Interior; Repair group 68; Dash panel; Removing driver's shelf

• ‒ Connect vehicle diagnostic, testing and information system VAS 5051 or fault reader V.A.G 1551 and select engine electronics control unit with "Address word" 01
  For this purpose, the ignition must be switched on.
• ‒ Initiate final control diagnosis and actuate ACF solenoid -N80.

• ‒ → Fuel pump relay (in the central electric's, electronics box, passenger's footwell, position 4) should pull and fuel pump should run.

A - If relay does not respond:

• ‒ Check voltage supply of fuel pump relay => Page 24-56.
• ‒ Checking actuation of fuel pump relay
  .

B - If relay is energised but fuel pump does not run:

• ‒ Check voltage supply for fuel pump and components (via fuel pump relay) .

Checking voltage supply of fuel pump relay

• ‒ Disconnect fuel pump relay.
• ‒ → Connect the multimeter to contact 17 of relay socket and earth to measure voltage.
• ‒ Specified value: approx. battery voltage

If specified value is not attained:

• ‒ Replace central electric's.

Checking actuation of fuel pump relay

• ‒ Switch ignition off.
• ‒ Connect the V.A.G 1598/31 test box to wiring harness leading to engine control unit; the engine control unit should not be connected => Page 24-17.
• ‒ Jumper contacts 1 and 65 at test box with leads from adapter set V.A.G 1594A.

• ‒ → Fuel pump relay (on central electrics in passenger's footwell, position 4) must pull.

If the relay pulls now, but not during final control diagnosis:

• ‒ Fit a new engine control unit => Page 24-22.

If the relay does not pick up:

• ‒ Disconnect cable link.
• ‒ Disconnect fuel pump relay.

• ‒ → Connect the multimeter to contact 19 of relay socket and earth to measure voltage.
• ‒ Specified value: approx. battery voltage

If specified value is not attained:

• ‒ Check the wiring connections.

=> Current Flow Diagrams, Electrical Fault-Finding and Fitting Locations

If specified value is attained:

• ‒ → Check for open circuit and short to positive or earth in the following wiring connection:

• ‒ Rectify any open/short circuit as necessary.

If no fault is found:

• ‒ Replace the fuel pump relay -J17.
• ‒ Reconnect engine control unit.

Checking voltage supply of fuel pump and components

• ‒ → Disconnect fuses S228, S229 and S234 (positions 28, 29 and 34) in fuse holder.
• ‒ Initiate final control diagnosis and actuate ACF solenoid -N80.

• ‒ To measure the voltage, connect multimeter to earth and to one of the contacts of the following fuses in the fuse holder.

If specified values are not attained:

• ‒ Repeat the test at the other contact of the fuse base.

If the specified values are still not attained:

• ‒ Check the wiring connections.

=> Current Flow Diagrams, Electrical Fault-Finding and Fitting Locations

If no fault is found:

• ‒ Replace the fuel pump relay -J17.
• ‒ Reinsert the fuses.