skoda Workshop Repair Guides

Skoda Workshop Service and Repair Manuals

ABOUT US
Self-diagnosis for airbag system II > < Ending output

Fabia Mk1

Coding airbag control unit
Coding airbag control unit
  Note
Coding is necessary if a new airbag control unit is used.
Conditions:
l  Warning lamp for airbag -K75- flashes continuously.
l  Airbag control unit -J234- was replaced.
   
Readout on display:
–  Enter function 07.
  
Vehicle system test                 HELP
Select function XX
Readout on display:
–  Confirm the entry with key Q.
  
Vehicle system test                   Q
Coding control unit
Readout on display:
–  Enter code number in accordance with the table and confirm with Q.
  
Coding control unit
Enter code number XXXXX        (0-32767)
Vehicle equipmentParts No.Control unit code number
Driver airbag
belt tensioner (electrically ignited)
side airbags		6Q0 909 605 H 01 → Note12337
6Q0 909 605 H 07 → Note12343
1C0 909 605 H 07 → Note12343
1C0 909 605 K 04 → Note12340
Driver and front passenger airbag
belt tensioner (electrically ignited)
side airbags		6Q0 909 605 H 02 → Note12338
6Q0 909 605 H 08 → Note12344
1C0 909 605 H 08 → Note12344
1C0 909 605 K 05 → Note12341
Driver airbag
belt tensioner (electrically ignited)		6Q0 909 605 H 03 → Note12339
6Q0 909 605 H 09 → Note12345
1C0 909 605 H 09 → Note12345
1C0 909 605 K 06 → Note12342
Driver and front passenger airbag
belt tensioner (electrically ignited)		6Q0 909 605 H 04 → Note12340
6Q0 909 605 H 0A → Note12353
1C0 909 605 H 0A → Note12353
1C0 909 605 K 07 → Note12343
Driver airbag
belt tensioner (mechanically ignited)		6Q0 909 601 C 01 → Note12337
 
1C0 909 601 C 01 → Note12337
1C0 909 601 A 0T → Note12372
Driver and front passenger airbag
belt tensioner (mechanically ignited)		6Q0 909 601 C 02 → Note12338
1C0 909 601 C 02 → Note12338
1C0 909 601 A 11 → Note12593
Driver and front passenger airbag
belt tensioner (mechanically ignited)
switch for front passenger airbags		1C0 909 601 A 0S → Note12371
Driver and front passenger airbag
belt tensioner (mechanically ignited)
side airbags
switch for front passenger airbags		1C0 909 605 K 01 → Note12337
Driver and front passenger airbag
belt tensioner (electrically ignited)
switch for front passenger airbags		1C0 909 605 K 02 → Note12338

1)  Valid for vehicles ? 11.00
2)  Valid for vehicles 12.00 ? 02.01
3)  Valid for vehicles 03.01 ? 07.02
4)  Valid for vehicles 08.02 ?
   
–  If the following message is displayed, the coding is done:
The control unit identification number, the control unit code number and the workshop code are displayed.
–  Press → key.
  
6Q0909605 H   02 AIRBAG VW5     0003 →
Coding 12338                   WSC XXXXX
Readout on display:
–  Ending output → Chapter.
  
Vehicle system test                 HELP
Select function XX
–  If the following message is displayed after entering the code number, the coding is incorrect:
In this case the control unit was not coded with the data required for the vehicle. Check whether the right control unit was fitted on the vehicle (compare part number and character index), or whether possibly a wrong code was entered.
–  Repeat coding.
If the control unit cannot be coded (correct control unit, correct code number) the control unit is defective.
–  Replace the control unit with a new original part and repeat coding.
  
Fault                                 →
Coding XXXXX not accepted

Self-diagnosis for airbag system II > < Ending output