skoda Workshop Repair Guides

Skoda Workshop Service and Repair Manuals

ABOUT US
Adapt service interval display - SID > < Reading measured value block

Octavia Mk1

Adjustment
Adjustment
The following changes can be made and stored with the “Adaptation” function:
t  correction of momentary fuel consumption gauge
t  adjustment (reset) of service interval display (SID)
t  adjustment of odometer when the dash panel insert is replaced
t  correction of fuel tank sender characteristic curve
What are retrieved are the individual functions by entering the respective number of the adjustment channel (see adjustment table → Anchor).
Adjustment table:
   
adjustment channeladjustment function
03adjustment of momentary fuel consumption gauge → Anchor
04Language versions of multi-function display (not assigned)
09Odometer/mileage reading display → Anchor
10SID residual value for oil service after changing dash panel insert → Chapter
11SID residual value for service inspection (distance) after changing dash panel insert → Chapter
12SID residual value for service inspection (time) after changing dash panel insert → Chapter
30Adjustment of the fuel tank sender characteristic curve → Chapter

Performing function 10 “Adaptation”
   
–  Readout on display:
–  Enter function 10 and confirm with key Q.
  
Vehicle system test               HELP
Select function XX
Readout on display:
–  Enter the desired adjustment channel (adjustment table → Anchor).
  Note
After changing an adaptation value or ending an adaptation channel, it is once again necessary to perform the function 10 “Adaptation” in order to select another adaptation channel!
Adjust momentary fuel consumption gauge
  Note
t  Adjustment only on vehicles fitted with multi-function display.
t  It is only possible to make an entry of between 85% and 115%.
t  The entry must be made in steps of 5%.
–  Enter 03 (channel number).
–  Confirm the entry with key Q.
  
Adjustment
Enter channel number XX
Readout on display:
–  Press → key.
  Note
The correction of the momentary fuel consumption gauge is only possible via the direct entry!
  
Channel  03     Adaptation        100  ->
                     (- ↑   ↓ -)
Readout on display:
–  Enter the desired correction value via the keypad of the vehicle system tester, to do so fill in "0" as the first digits.
Example:
Specified value: 90 %
Entry value: 00090
  
Channel  03           Adaptation    100
Enter adaptation value  XXXXX
Readout on display:
–  Confirm the entry with key Q.
  
Channel  03        Adaptation     100  Q
Enter adaptation value   00090
Readout on display:
–  Confirm the entry with key Q.
  
Channel  03           Adaptation   90  Q
Store changed value?
Readout on display:
–  Deactivate the adjustment of momentary fuel consumption gauge with the key →.
  
Channel  03     Adaptation        90  ->
Changed value stored
Readout on display:
Odometer/mileage reading display
The odometer/mileage reading of the distance counter can be updated with this channel when changing the dash panel insert.
  Note
t  The adjustment is only possible for a dash panel insert with an odometer reading of up to max. 100 km.
t  The adjustment is only possible once for each dash panel insert.
t  Only a greater adaptation value can be entered.
  WARNING
It is no longer possible to correct the entry if an incorrect entry is made and confirmed. The dash panel insert must then be replaced with a new one again.
t  In countries with a speedometer reading in mileage, the adaptation must also be carried out in kilometres! For this purpose, convert the adaptation value from miles into kilometres (1 mile = 1.609 km).
t  Observe the instructions when changing the dash panel insert → Chapter!
  
Vehicle system test               HELP
Select function XX
Readout on display:
–  Enter 11.
  
Vehicle system test               HELP
Select function XX
Readout on display:
–  Confirm the entry with key Q.
  
Vehicle system test                   Q
11 - Login procedure
Readout on display:
–  Enter code number 13861 and confirm entry with key Q.
  
Login procedure
Enter code number XXXXX
Readout on display:
–  Enter function 10 and confirm with key Q.
  
Vehicle system test               HELP
Select function XX
Readout on display:
–  Enter 09 (channel number) and confirm entry with key Q.
  
Adjustment
Enter channel number XX
Readout on display:
  Note
Only a direct entry is possible using the keypad of the vehicle system tester -V.A.G 1552 -!
–  Move forward in test program with key →.
  
Channel 09          Adaptation      0 ->
                                <-↑  ↓->
Readout on display:
Example:
Kilometre reading = 89627
0 8 9 6 3
  
Channel 09          AAdaptation    0    Q
Enter adaptation value  XXXXX
X    Hundred thousands: 100000 ... 900000 km
 X   Ten thousands: 10000 ... 90000 km
  X  Thousands: 1000 ... 9000 km
   X Hundreds: 100 ... 900 km
    XTens: 10 ... 90 km
     Ones: rounded up to the next ten

–  Enter adaptation values with the keypad.
   
Readout on display:
–  Confirm the entry with key Q.
  
Channel 09          Adaptation    0    Q
Enter adaptation value  08963
Readout on display:
The km reading entered now appears in the display of the dash panel insert.
If the displayed km reading is not O.K., e.g. because an incorrect entry was made:
–  Press key C and repeat the entry with the correct adaptation value.
If the displayed km reading in the display of the dash panel insert is O.K.:
–  Confirm the entry with key Q.
  
Channel 09      Adaptation    8963     Q
                                <-↑  ↓->
Readout on display:
–  Confirm the entry with key Q.
  
Channel 09     Adaptation     8963     Q
Store changed value?
Readout on display:
–  End the adjustment of the kilometre reading on the display with the key →.
  
Channel 09    Adaptation      8963    ->
Changed value stored
Readout on display:
  
Vehicle system test               HELP
Select function XX

Adapt service interval display - SID > < Reading measured value block