Special Service Tools
|
KM-135 |
Adapter |
|
To measure engine oil pressure in conjunction with KM-498-B |
|
KM-194-C |
Spark Plug Wrench |
|
To remove/install spark plug |
|
KM-263-B |
Engine Bridge |
|
To hold/lift the engine |
|
KM-301 |
Gauge Bar |
|
To check piston projection |
|
KM-340-1-E |
Cutter Set |
|
To cut and correct valve seating |
|
KM-348 |
Spring Compressor |
|
To compress valve spring in conjunction with KM-653 |
| 
|
Special tools (continuation)
|
KM-412 |
Engine Assembly Stand |
|
To hold removed engine |
|
KM-412-13 |
Adapter |
|
To hold engine in conjunction with KM-412 |
|
KM-417 |
Assembly Sleeve |
|
To press crankshaft seal ring into oil pump housing |
|
KM-422 |
Installer |
|
To press seal ring in camshaft |
|
KM-427 |
Remover/Installer |
|
To install guide pins into engine block |
|
KM-470-B |
Angular Torque Wrench |
|
To tighten cylinder head bolts |
| 
|
Special tools (continuation)
|
KM-471 |
Adapter |
|
To check pressurised cooling system in conjunction with cooling system tester |
|
KM-498-B |
Pressure Gauge |
|
To check engine oil pressure in conjunction with KM-135 |
|
MKM-571-B |
Dial Gauge |
|
To check various components |
|
MKM-596-A |
Measuring equipment |
|
To measure oil temperature |
|
MKM-604-C |
Torx Bit and Socket Set |
|
To remove/install Torx bolts |
|
KM-609 |
Electronic Kit I |
|
To diagnose electrical and electronic systems |
| 
|
Special tools (continuation)
|
MKM-610 |
Torque Wrench, 1/2"" |
|
Measuring range: 30 - 130 Nm 22 - 96 lbf. ft. |
|
MKM-611 |
Torque Wrench, 3/8"" |
|
Measuring range: 10 - 60 Nm/7 - 44 lbf. ft. |
|
KM-652 |
Locking Device |
|
To lock flywheel or drive disc |
|
KM-653-A |
Adapter |
|
To tension valve spring in conjunction with KM-348 |
|
KM-658 |
Installer |
|
To install rear crankshaft seal ring |
|
MKM-669 |
Torque Wrench, 1/2"" |
|
Measuring range 50 - 300 Nm |
| 
|
Special tools (continuation)
|
KM-726-A |
Oil Filter Wrench |
|
Removal and installation of oil filter |
|
KM-728 |
Remover/Installer |
|
To remove/install the knock sensor |
|
KM-805 |
Reamer |
|
To ream the valve guide, oversize 0.075 mm |
|
KM-835-A |
Installer |
|
To install the valve stem seal |
|
KM-836 |
Remover |
|
To remove spark plug connector |
|
KM-840 |
Removing Pliers |
|
To remove valve stem seals |
| 
|
Special tools (continuation)
|
KM-845 |
Suctioner |
|
To remove the hydraulic valve lifters |
|
KM-852 |
Locking Tool |
|
To lock the camshaft sprockets |
|
MKM-883-1 |
Engine Bridge |
|
To hold/lift the engine |
|
MKM-889 |
Remover/Installer |
|
To remove/install the valve stem seals (cylinder head installed) |
|
KM-911 |
Locking Device |
|
To lock flywheel/drive disc |
|
KM-913-A |
Tensioning Wrench, Ribbed V-belt |
|
To tension/relax the ribbed V-belt tension roller |
| 
|
Special tools (continuation)
|
KM-2355 |
Socket Wrench |
|
To loosen/tighten cylinder head bolts |
|
KM-J-34730-91 |
Pressure Tester |
|
To check fuel pressure |
| 
|
|
