vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-056 Fuse FE14 Circuit > < C-054 Fuse FE12 Circuit

Astra H

C-055 - Fuse FE13 Circuit

Test

Work Order Description

Nominal Value
T001

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Vehicle with REC (Rear Electronic Module)
Yes: No:
T002

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Reconnect all disconnected components
  • All consumers turned off
  • Insert new fuse FE13 and then check the fuse for proper operation.

Test okay?
Yes: No:
T003

Check: Short to Ground of Voltage Supply Circuit
  • Ignition ON
  • Switch fog lamps on
  • Check the following component for proper operation:
    FE13 Fuse

Test okay?
Yes: No:
T004

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    K16_X125 Relay - Fog Lamp, Front
  • Connect fused jumper wire to:
    K16_X125 Relay - Fog Lamp, Front
    Socket Terminal 87
    &
    Battery voltage
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T005

Check: Short to Ground of Voltage Supply Circuit
  • Remove fused jumper wire
  • Remove electrical component from socket:
    X125 Underhood Electronic Module
  • Connect fused jumper wire to:
    X125 Underhood Electronic Module
    Socket Terminal 49 (XE1)
    &
    Battery voltage
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T006

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Reconnect all disconnected components
  • All consumers turned off
  • Ignition ON
  • Insert new fuse FE13 and then check the fuse for proper operation.

Test okay?
Yes: No:
T007

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    X125 Underhood Electronic Module
  • Ignition ON
  • Insert new fuse FE13 and then check the fuse for proper operation.

Test okay?
Yes: No:
T008

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E82 Lamp - Glove Box
  • Connect fused jumper wire to:
    X125 Underhood Electronic Module
    Socket Terminal 48 (XE1)
    &
    Battery voltage
  • Ignition ON
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T009

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Van
Yes: No:
T010

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E62L Lamp - Trunk, Left
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
  • Connect each of the following components/control units consecutively to the wiring harness and repeat the check each time:
    E62R Lamp - Trunk, Right

Test okay?
Yes: No:
T011

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Anti-Theft Warning with Central Door Locking
Astra-H, Reading Lamp, Rear
Astra-H, Phone (Preparation)
Astra-H, CD 50
Astra-H, CD 60
Astra-H, CDC 80
Yes: No:
T012

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E1_E68 Lamp - Passenger Compartment
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T013

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Sunshade Lamp, Left and Right
Yes: No:
T014

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E120L Lamp - Sunshade, Left
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the check each time:
    E120R Lamp - Sunshade, Right

Test okay?
Yes: No:
T015

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Reading Lamp, Rear
Yes: No:
T016

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Front Electrical Sliding Roof
Yes: No:
T017

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E1_M16 Lamp - Passenger Compartment, Rear
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T018

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E94 Lamp - Passenger Compartment, Rear
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T019

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Sunshade Lamp, Left Only
Yes: No:
T020

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E120L Lamp - Sunshade, Left
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T021

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Sunshade Lamp, Right Only
Yes: No:
T022

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E120R Lamp - Sunshade, Right
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T023

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E67 Lamp - Passenger Compartment
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:
T024

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    E62 Lamp - Trunk
  • Ignition ON
  • Insert new fuse into the socket of the fused jumper wire and then check this fuse for proper operation.

Test okay?
Yes: No:


Result

Cause Of Fault
E001 Result: System Overload
  • A temporary current overload in the system behind fuse FE13 has occurred

Note:

In case of a temporary current overload, the cause for the blow of the fuse may be located in a circuit behind the control unit/component.

These circuits should be checked additionally for short to ground.
E002 Result: Defective Component
  • If the nominal value is reached during one of the measurements, the component/control unit that has been disconnected immediately before that measurement is defective.
E003 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Socket Terminal 48 (XE1)
    &
    E69L Fog Lamp - Front, Left
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    E69L Fog Lamp - Front, Left
    or
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E004 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Socket Terminal 49 (XE1)
    &
    E69R Fog Lamp - Front, Right
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    E69R Fog Lamp - Front, Right
E005 Result: Defective Component
  • Defective component:
    K16_X125 Relay - Fog Lamp, Front
    or
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E006 Result: System Overload
  • A temporary current overload in the system behind fuse FE13 has occurred
E007 Result: Defective Component
  • Defective component:
    E82 Lamp - Glove Box
E008 Result: Defective Component
  • If the nominal value is reached during one of the measurements, the component/control unit that has been disconnected immediately before that measurement is defective.
E009 Result: Defective Component
  • Defective component:
    E1_E68 Lamp - Passenger Compartment
E010 Result: Defective Component
  • If the nominal value is reached during one of the measurements, the component/control unit that has been disconnected immediately before that measurement is defective.
E011 Result: Defective Component
  • Defective component:
    E1_M16 Lamp - Passenger Compartment, Rear
E012 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Socket Terminal 48 (XE1)
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session
E013 Result: Defective Component
  • Defective component:
    E94 Lamp - Passenger Compartment, Rear
E014 Result: Defective Component
  • Defective component:
    E120L Lamp - Sunshade, Left
E015 Result: Defective Component
  • Defective component:
    E120R Lamp - Sunshade, Right
E016 Result: Defective Component
  • Defective component:
    E67 Lamp - Passenger Compartment
E017 Result: Defective Component
  • Defective component:
    E62 Lamp - Trunk
E018 Result: Defective Component
  • Defective component:
    X125 Underhood Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.





C-056 Fuse FE14 Circuit > < C-054 Fuse FE12 Circuit