vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-005 Pedal Position Sensor Circuit > < C-003 5V Circuit 1

Astra H

C-004 - 5V Circuit 2

Test

Work Order Description

Nominal Value
T001

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B176 Sensor - Rail Fuel Pressure
    Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T002

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B150 Sensor - Boost Pressure
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T003

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B22 Sensor - Pedal Position
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T004

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B28 Sensor - Camshaft
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T005

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    Y56 Solenoid Valve - Exhaust Gas Recirculation
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T006

Check: Component
  • Ignition OFF
    Disconnect wiring harness connector from:
    B175 Sensor - Pressure, Exhaust Gas
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T007

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Air Conditioning (not ECC)
Astra-H, Electronic Climate Control ECC
Astra-H, Automatic Climate Control SAC
Yes: No:
T008

Check: Component
  • Ignition OFF
    Disconnect wiring harness connector from:
    B18 Sensor - Pressure, Air Conditioning
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P0651 with status PRESENT stored?
Yes: No:
T009

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
    Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 62 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T010

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 62 (XC97)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T011

Check: Short to Voltage of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC96 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T012

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC96)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T013

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 61 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T014

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 61 (XC96)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T015

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 64 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T016

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 64 (XC97)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T017

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 60 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T018

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 60 (XC97)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T019

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 63 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T020

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 63 (XC97)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T021

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Air Conditioning (not ECC)
Astra-H, Electronic Climate Control ECC
Astra-H, Automatic Climate Control SAC
Yes: No:
T022

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T023

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T024

Check: Short to Ground of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T025

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE3 )
  • Ignition ON
  • Measure voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T026

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC96 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 29 (XC27)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T027

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 16 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T028

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE3 )
    Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 16 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T029

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE3 )
  • Ignition ON
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 29 (XC27)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T030

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 39 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T031

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T032

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 34 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T033

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T034

Check: Short to Voltage of Signal Circuit
Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC96 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 28 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T035

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T036

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
  • Ignition ON
  • Measure voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T037

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 28 (XC96)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T038

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 35 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T039

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 11 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T040

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC97 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 36, 37 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T041

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 12 (XC97)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E002 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 30 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    X125 Underhood Electronic Module
E003 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE3)
E004 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 30 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    X125 Underhood Electronic Module
E005 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC96)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE3)
E006 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 63 (XC97)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 1
E007 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 63 (XC97)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 1
E008 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 60 (XC97)
    &
    Y56 Solenoid Valve - Exhaust Gas Recirculation
    Wiring harness connector (wiring harness side) terminal 1
E009 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 60 (XC97)
    &
    Y56 Solenoid Valve - Exhaust Gas Recirculation
    Wiring harness connector (wiring harness side) terminal 1
E010 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 64 (XC97)
    &
    B28 Sensor - Camshaft
    Wiring harness connector (wiring harness side) terminal 1
E011 Result: Short to Voltage
  • Short to voltage/ground of circuit between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 64 (XC97)
    &
    B28 Sensor - Camshaft
    Wiring harness connector (wiring harness side) terminal 1
E012 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 61 (XC96)
    &
    B150 Sensor - Boost Pressure
    Wiring harness connector (wiring harness side) terminal 3
    &
    C8 Capacitor - Boost Pressure Sensor
    Wiring harness connector (wiring harness side) terminal 3
E013 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 61 (XC96)
    &
    B150 Sensor - Boost Pressure
    Wiring harness connector (wiring harness side) terminal 3
    &
    C8 Capacitor - Boost Pressure Sensor
    Wiring harness connector (wiring harness side) terminal 3
E014 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC96)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) wiring colour BKYE

Note:

Wiring colours: BK=Black, BN=Brown, BU=Blue, GD=Gold, GN=Green, GY=Grey, OG=Orange, PK=Pink, RD=Red, SR=Silver, TQ=Turquoise, VT=Violet, WH=White, YE=Yellow,
L=Light, D=Dark

E015 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC96)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) wiring colour BKYE

Note:

Wiring colours: BK=Black, BN=Brown, BU=Blue, GD=Gold, GN=Green, GY=Grey, OG=Orange, PK=Pink, RD=Red, SR=Silver, TQ=Turquoise, VT=Violet, WH=White, YE=Yellow,
L=Light, D=Dark

E016 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 62 (XC97)
    &
    B176 Sensor - Rail Fuel Pressure
    Wiring harness connector (wiring harness side) wiring colour BKWH

Note:

Wiring colours: BK=Black, BN=Brown, BU=Blue, GD=Gold, GN=Green, GY=Grey, OG=Orange, PK=Pink, RD=Red, SR=Silver, TQ=Turquoise, VT=Violet, WH=White, YE=Yellow,
L=Light, D=Dark

E017 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 62 (XC97)
    &
    B176 Sensor - Rail Fuel Pressure
    Wiring harness connector (wiring harness side) wiring colour BKWH

Note:

Wiring colours: BK=Black, BN=Brown, BU=Blue, GD=Gold, GN=Green, GY=Grey, OG=Orange, PK=Pink, RD=Red, SR=Silver, TQ=Turquoise, VT=Violet, WH=White, YE=Yellow,
L=Light, D=Dark

E018 Result: Defective Component
  • Defective component:
    B18 Sensor - Pressure, Air Conditioning
E019 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    X125 Underhood Electronic Module
E020 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 16 (XC96)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 7 (XE3)
E021 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    X125 Underhood Electronic Module
E022 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 29 (XC27)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 8 (XE3)
E023 Result: Defective Component
  • Defective component:
    B175 Sensor - Pressure, Exhaust Gas
E024 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC97)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 2
E025 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 39 (XC97)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 3
E026 Result: Defective Component
  • Defective component:
    Y56 Solenoid Valve - Exhaust Gas Recirculation
E027 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 10 (XC97)
    &
    Y56 Solenoid Valve - Exhaust Gas Recirculation
    Wiring harness connector (wiring harness side) terminal 2
E028 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 34 (XC97)
    &
    Y56 Solenoid Valve - Exhaust Gas Recirculation
    Wiring harness connector (wiring harness side) terminal 3
E029 Result: Defective Component
  • Defective component:
    B28 Sensor - Camshaft
E030 Result: Defective Component
  • Defective component:
    B22 Sensor - Pedal Position
    or
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E031 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5

or

  • Defective component:
    X125 Underhood Electronic Module
E032 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC96)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 43 (XE3)
E033 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6

or

  • Defective component:
    X125 Underhood Electronic Module
E034 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 28 (XC96)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)
E035 Result: Defective Component
  • Defective component:
    B150 Sensor - Boost Pressure
E036 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 11 (XC97)
    &
    B150 Sensor - Boost Pressure
    Wiring harness connector (wiring harness side) terminal 2
    &
    C8 Capacitor - Boost Pressure Sensor
    Wiring harness connector (wiring harness side) terminal 2
E037 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 35 (XC97)
    &
    B150 Sensor - Boost Pressure
    Wiring harness connector (wiring harness side) terminal 1
    &
    C8 Capacitor - Boost Pressure Sensor
    Wiring harness connector (wiring harness side) terminal 1
E038 Result: Defective Component
  • Defective component:
    B176 Sensor - Rail Fuel Pressure

Important:

After replacing the following component the programming function for the replacement of the corresponding component has to be performed by using the diagnostic tester:

B176 Sensor - Rail Fuel Pressure
E039 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 12 (XC97)
    &
    B176 Sensor - Rail Fuel Pressure
    Wiring harness connector (wiring harness side) terminal 3
E040 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 36, 37 (XC97)
    &
    B176 Sensor - Rail Fuel Pressure
    Wiring harness connector (wiring harness side) terminal 2





C-005 Pedal Position Sensor Circuit > < C-003 5V Circuit 1