vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
B-003 Diagnostic System Check > < B-001 DIAGNOSTIC TROUBLE CODE

Astra H

B-002 - DATA LIST

Test

Work Order Description

Nominal Value
T001 Tester Display Battery Voltage
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 1 .
11 ... 13.5 V
  • Engine starting
greater than 8 V
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
12 ... 15 V
Concerned Terminals:
ECM: 64 (XC4)
  
Yes: No:
T002 Tester Display Fuel Pump Relay
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 1 .
Inactive
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
Active
Concerned Terminals:
ECM: 49 (XC4)
  
Yes: No:
T003 Tester Display APP at Idle Position (Accelerator Pedal Position)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
Active
  • Accelerator pedal slightly actuated
Inactive
Concerned Terminals:
ECM: 24, 25, 26, 27, 53, 54 (XC4)
  
Yes: No:
T004 Tester Display APP Sensor 1 (Accelerator Pedal Position)
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
less than 1 V
  • Accelerator pedal slightly actuated
1 ... 4 V
  • Accelerator pedal actuated to full load stop
greater than 4 V
Concerned Terminals:
ECM: 24, 25, 26, 27, 53, 54 (XC4)
  
Yes: No:
T005 Tester Display APP Sensor 2 (Accelerator Pedal Position)
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
less than 0.5 V
  • Accelerator pedal slightly actuated
0.7 ... 1.5 V
  • Accelerator pedal actuated to full load stop
greater than 2.0 V
Concerned Terminals:
ECM: 24, 25, 26, 27, 53, 54 (XC4)
  
Yes: No:
T006 Tester Display Calculated Pedal Position
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
0 %
  • Accelerator pedal actuated to full load stop
greater than 90 %
Concerned Terminals:
ECM: 24, 25, 26, 27, 53, 54 (XC4)
  
Yes: No:
T007 Tester Display TP Sensor 1 (Throttle Position)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
less than 0.65 V
  • Accelerator pedal slightly actuated
0.7 ... 2.0 V
  • Accelerator pedal briefly actuated to full load stop
greater than 2.0 V
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T008 Tester Display TP Sensor 2 (Throttle Position)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
greater than 4.2 V
  • Accelerator pedal slightly actuated
less than 4.0 V
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T009 Tester Display Calculated Throttle Position
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
less than 5 %
  • Accelerator pedal briefly actuated to full load stop
greater than 10 %
Value changing briefly
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T010 Tester Display Throttle Position PWM Servo Signal
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
greater than 90 %
  • Accelerator pedal briefly actuated to full load stop
less than 90 %
Value changing briefly
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T011 Tester Display Throttle Position
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
Idle
  • Accelerator pedal slightly actuated
Partial Load
  • Accelerator pedal briefly actuated to full load stop
Full Load
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T012 Tester Display TP Sensor 1 Learned Lower Position (Throttle Position)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
less than 1.0 V
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T013 Tester Display TP Sensor 2 Learned Lower Position (Throttle Position)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
greater than 2.0 V
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T014 Tester Display Desired Engine Idle Speed
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 1 .
650 ... 950 rpm
Concerned Terminals:
ECM: 8, 9, 31, 32, 40, 41, 47, 48 (XC3)
  
Yes: No:
T015 Tester Display Engine Speed
  • Ignition ON
  • Engine starting

Note:

This data list parameter is in the data list 1 .
greater than 60 rpm
Concerned Terminals:
ECM: 35, 39, 42 (XC3)
  
Yes: No:
T016 Tester Display Brake Switch 1
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Brake pedal not actuated

Note:

This data list parameter is in the data list 1 .
Inactive
  • Brake pedal actuated
Active
Concerned Terminals:
ECM: 45, 57 (XC4)
  
Yes: No:
T017 Tester Display Brake Switch 2
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Brake pedal not actuated

Note:

This data list parameter is in the data list 1 .
Inactive
  • Brake pedal actuated
Active
Concerned Terminals:
ECM: 45, 57 (XC4)
  
Yes: No:
T018 Tester Display Clutch Switch
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Do not actuate clutch pedal

Note:

This data list parameter is in the data list 1 .

  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Cruise Control)
Inactive
  • Clutch pedal actuated
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Cruise Control)
Active
Concerned Terminals:
ECM: 16 (XC4)
  
Yes: No:
T019 Tester Display Park/Neutral Switch
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Brake pedal actuated
  • Selector lever in position P - N

Note:

This data list parameter is in the data list 1 .

  
(Astra-H), (Front Wheel Drive, Automatic Transmission, AF 17-4)
P - N
(Astra-H), (Front Wheel Drive, Manual Transmission)
Not Used
  • Selector lever in position R - D
  
Default
Not Used
(Astra-H), (Front Wheel Drive, Automatic Transmission, AF 17-4)
R - D
Concerned Terminals:
ECM: -
  
Yes: No:
T020 Tester Display Vehicle Speed
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))

Note:

This data list parameter is in the data list 1 .
30 km/h
19 mph
Diagnostic tester display converges to speedometer display
Concerned Terminals:
ECM: -
  
Yes: No:
T021 Tester Display Cruise Control Tip Switch
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Key " I " not pressed

Note:

This data list parameter is in the data list 1 .

  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Key " I " pressed briefly
  
Default
Not Programmed
(Electronic Cruise Control)
I (set)
  • Key " R " not pressed
  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Key " R " pressed briefly
  
Default
Not Programmed
(Electronic Cruise Control)
R (Resume)
  • Key " O " not pressed
  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Key " O " pressed briefly
  
Default
Not Programmed
(Electronic Cruise Control)
O (off)
Concerned Terminals:
CIM: 1, 2, 3 (XC48)
  
Yes: No:
T022 Tester Display Cruise Control
  • Engine running at idle speed, operating temperature
  • Brake pedal actuated
  • Vehicle stationary
  • Key " I " not pressed

Note:

This data list parameter is in the data list 1 .

  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Vehicle travelling (constant speed, approximately 40 km/h (25 mph))
  • Brake pedal not actuated
  • Clutch pedal not actuated/selector lever in position D
  • Cruise control active
  
Default
Not Programmed
(Electronic Cruise Control)
Active
Concerned Terminals:
CIM: 1, 2, 3 (XC48)
  
Yes: No:
T023 Tester Display Vehicle Speed in Cruise Control Range
  • Vehicle accelerated from stop (from 0 km/h (0 mph) up to approximately 18 km/h (11 mph))

Note:

This data list parameter is in the data list 1 .

  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Cruise Control)
Inactive
  • Vehicle speed is greater than 30 km/h (19 mph)
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Cruise Control)
Active
Concerned Terminals:
CIM: 1, 2, 3 (XC48)
  
Yes: No:
T024 Tester Display Mass Air Flow Sensor
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .

During model year 2008 the following changes occur:

The component B69 is no longer installed
7 ... 19 kg/h
0.2 ... 1.2 V
Concerned Terminals:
ECM: 28, 59 (XC3)
  
Yes: No:
T025 Tester Display Manifold Absolute Pressure
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 2 .

During model year 2008 the following changes occur:

The component B67 is additionally installed
80 ... 106 kPa
3.0 ... 4.8 V
With the engine OFF, the ambient air pressure is displayed.
Concerned Terminals:
ECM: 42, 45, 51 (XC3)
  
Yes: No:
T026 Tester Display Intake Air Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
10 ... 80 °C
50 ... 176 °F
2.0 ... 0.8 V
 
Yes: No:
T027 Tester Display Coolant Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
80 ... 110 °C
176 ... 230 °F
2.0 ... 0.5 V
Concerned Terminals:
ECM: 25, 60 (XC3)
  
Yes: No:
T028 Tester Display Oil Level
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 2 .
Normal
Concerned Terminals:
ECM: 36, 43 (XC4)
  
Yes: No:
T029 Tester Display Oil Pressure
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 2 .
Low Pressure
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
Normal
Concerned Terminals:
ECM: 5 (XC3)
  
Yes: No:
T030 Tester Display Engine Oil Level Status
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 2 .
Okay
Concerned Terminals:
ECM: 36, 43 (XC4)
  
Yes: No:
T031 Tester Display Fuel Tank Ventilation Valve
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
Inactive
0 %
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
Active
greater than 0 %
Concerned Terminals:
ECM: 46 (XC3)
  
Yes: No:
T032 Tester Display Deceleration Fuel Cutoff
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
Inactive
  • Vehicle travelling (coasting, approximately 30 km/h (19 mph))
Active
Value changing briefly
Concerned Terminals:
ECM: -
  
Yes: No:
T033 Tester Display Knock Control
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
Inactive
  • Accelerator pedal briefly actuated to full load stop
Active
Value changing briefly
Concerned Terminals:
ECM: 10, 27, 44 (XC3)
  
Yes: No:
T034 Tester Display Knock Retard Cylinder 1
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
0 °CA
  • Accelerator pedal briefly actuated to full load stop

Note:

Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
greater than 0 °CA
Concerned Terminals:
ECM: 10, 27, 44 (XC3)
  
Yes: No:
T035 Tester Display Knock Retard Cylinder 2
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
0 °CA
  • Accelerator pedal briefly actuated to full load stop

Note:

Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
greater than 0 °CA
Concerned Terminals:
ECM: 10, 27, 44 (XC3)
  
Yes: No:
T036 Tester Display Knock Retard Cylinder 3
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
0 °CA
  • Accelerator pedal briefly actuated to full load stop

Note:

Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
greater than 0 °CA
Concerned Terminals:
ECM: 10, 27, 44 (XC3)
  
Yes: No:
T037 Tester Display Knock Retard Cylinder 4
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
0 °CA
  • Accelerator pedal briefly actuated to full load stop

Note:

Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
greater than 0 °CA
Concerned Terminals:
ECM: 10, 27, 44 (XC3)
  
Yes: No:
T038 Tester Display Full Load Enrichment
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 2 .
Inactive
  • Accelerator pedal briefly actuated to full load stop
Active
Value changing briefly
Concerned Terminals:
ECM: -
  
Yes: No:
T039 Tester Display Fan Control 1
  • Engine running
  • Air conditioning system OFF
  • Coolant temperature is less than 97 °C (207 °F)

Note:

This data list parameter is in the data list 2 .
Inactive
  • Coolant temperature between 97 °C (207 °F) and 99 °C (210 °F)
Active
Concerned Terminals:
ECM: 59 (XC4)
  
Yes: No:
T040 Tester Display Fan Control 2
  • Engine running
  • Coolant temperature is less than 99 °C (210 °F)

Note:

This data list parameter is in the data list 2 .
Inactive
  • Coolant temperature between 99 °C (210 °F) and 101 °C (214 °F)
Active
Concerned Terminals:
ECM: 10 (XC4)
  
Yes: No:
T041 Tester Display Intake Manifold Valve 1
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 2 .
Inactive
  • Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
Active
Concerned Terminals:
ECM: 3 (XC3)
  
Yes: No:
T042 Tester Display A/C Information Switch (Air Conditioning)
  • Engine idling
  • All consumers turned off
  • Air conditioning system switch OFF

Note:

This data list parameter is in the data list 3 .

  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Inactive
(Electronic Climate Control ECC)
Not Programmed
The data list parameter is invalid for this configuration
  • Air conditioning system switch ON
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Climate Control ECC)
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Active
Concerned Terminals:
ECM: 48 (XC4)
  
Yes: No:
T043 Tester Display A/C Pressure (Air Conditioning)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .

  
Default
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
320 ... 3100 kPa
(Electronic Climate Control ECC)
320 ... 3100 kPa
  • Air conditioning system switch ON
  
Default
The data list parameter is invalid for this configuration
(Electronic Climate Control ECC)
Is there a pressure difference of at least 500 kPa ?
(Air Conditioning (not ECC))
Is there a pressure difference of at least 500 kPa ?
Concerned Terminals:
ECM: 23, 39, 56 (XC4)
  
Yes: No:
T044 Tester Display A/C Cutoff Mode (Air Conditioning)
  • Engine idling
  • Coolant temperature between 60 °C (140 °F) and 115 °C (239 °F)
  • Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 3100 kPa ( 31 bar )
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .

  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
System OK
(Electronic Climate Control ECC)
System OK
Concerned Terminals:
ECM: 23, 39, 56 (XC4)
  
Yes: No:
T045 Tester Display A/C Relay (Air Conditioning)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .

  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Inactive
(Electronic Climate Control ECC)
Not Programmed
The data list parameter is invalid for this configuration
  • Air conditioning system switch ON
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Electronic Climate Control ECC)
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Active
Concerned Terminals:
ECM: 48 (XC4)
  
Yes: No:
T046 Tester Display B1S1 O2 Sensor Heater (Bank 1 Sensor 1)
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 3 .
Inactive
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
Active
Diagnostic tester displays alternately:
ACTIVE and INACTIVE
Concerned Terminals:
ECM: 58 (XC3)
  
Yes: No:
T047 Tester Display B1S2 O2 Sensor Heater (Bank 1 Sensor 2)
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

This data list parameter is in the data list 3 .
Inactive
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
Active
Diagnostic tester displays alternately:
ACTIVE and INACTIVE
Concerned Terminals:
ECM: 19 (XC3)
  
Yes: No:
T048 Tester Display B1S1 O2 Sensor (Bank 1 Sensor 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
50 ... 950 mV
Sensor signal alternates between high and low voltage range
Concerned Terminals:
ECM: 6, 23, 53 (XC3)
  
Yes: No:
T049 Tester Display B1S2 O2 Sensor (Bank 1 Sensor 2)
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))

Note:

This data list parameter is in the data list 3 .
50 ... 950 mV
Concerned Terminals:
ECM: 11, 29, 54 (XC3)
  
Yes: No:
T050 Tester Display B1 O2 Sensor Loop (Bank 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
Closed
Concerned Terminals:
ECM: 6, 23, 53 (XC3)
  
Yes: No:
T051 Tester Display B1S1 Air/Fuel Ratio (Bank 1 Sensor 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
Diagnostic tester displays alternately:
LEAN and RICH
Concerned Terminals:
ECM: 6, 23, 53 (XC3)
  
Yes: No:
T052 Tester Display B1S2 Air/Fuel Ratio (Bank 1 Sensor 2)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
Diagnostic tester displays alternately:
LEAN and RICH
Concerned Terminals:
ECM: 11, 29, 54 (XC3)
  
Yes: No:
T053 Tester Display B1 Short Term Fuel Trim (Bank 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
-5 ... 5 %
Concerned Terminals:
ECM: 6, 23, 53 (XC3)
  
Yes: No:
T054 Tester Display Catalyst Protection Enrichment (Bank 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

This data list parameter is in the data list 3 .
Inactive
  • Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))

Note:

Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
Active
Value changing briefly
Concerned Terminals:
ECM: 6, 23, 53 (XC3)
  
Yes: No:





B-003 Diagnostic System Check > < B-001 DIAGNOSTIC TROUBLE CODE