Vauxhall Workshop Service and Repair Manuals

SPECIAL SERVICE TOOLS - AUTOMATIC TRANSMISSION THM 125

KM-113-2           Base for Transmission Holder (in conjunction with KM-480)

KM-232               Adapter

       To check fluid pressure (line and governor pressure) in conjunction with KM-498-A (replacement for KM-J-5907)

KM-263 (S-1244)         Engine Lifter

       To lift engine

KM-305 (size 96)         Remover/Installer

       To press pump shaft bearing in and out in conjunction with drift and KM-J-28698

KM-313 (size 223)       Remover

       To drive needle bearing out of driving sprocket support, in conjunction with KM-483 and KM-J-26941

KM-396               Snap Ring Pliers

       To install and remove snap rings

KM-469-A           Remover/Installer

       To remove axle shaft seal ring in main case cover with Parts 5 and 13

KM-480               Holding Fixture

       To hold AT when overhauling (in conjunction with KM-113-2)

KM-481               Installer

       To install axle shaft snap ring

KM-482               Indicator Bolt Set

       To be used in conjunction with Dial Indicator Set MKM-572 or KM-J-8001 (or a commercially available dial gauge)

KM-483               Adapter

       To extract needle bearings from drive sprocket support in conjunction with KM-313 and KM-26941

KM-484               Adapter Ring

       To press together forward clutch spring set in conjunction with KM-J-23078-A

KM-485               Jacking Fixture (Adapter)

       To remove and install automatic transmission in conjunction with vehicle lifter

KM-498-A           Oil Pressure Gauge

       To check fluid pressure (line and governor pressure) in conjunction with KM-232 (replacement for KM-J-5907)

KM-502-A           Distance Ring

       To pull seal ring off main case and main case cover (in conjunction with MKM-557)

KM-507-B           Removal of Guide Joint

                            (replacement for KM-199-01)

KM-519               Ring Installer

       Turbine shaft seal ring

KM-531-A           Seal Installer

       To install piston in forward clutch

MKM-557           Remover

       To replace seal ring in main case and cover (in conjunction with KM-502-A)

KM-567               Remover/Installer

       To replace bushing in differential bearing for main case

MKM-572           Dial Indicator Set

                            (replacement for KM-J-8001)

       To measure axial play (in conjunction with KM-482)

KM-586               Remover Hook

       To drive out torque converter housing seal ring (in conjunction with KM-J-7004)

KM-598               Remover/Installer

       To press pump shaft bearing out and in - vehicles as of Model Year '85

KM-J-7004          Slide Hammer

       To drive out torque converter seal ring (in conjunction with KM-586)

KM-J-8092          Press Handle

       To use with KM-J-26938 and KM-J-28677

KM-J-23078-A    Clutch Spring Compressor

       To compress forward clutch spring set (in conjunction with KM-484)

KM-J-26938        Installer

       To press axle shaft seal ring into main case (in conjunction with KM-J-8092)

KM-J-26941        Bearing Puller

       To drive needle bearings from drive sprocket support in conjunction with KM-313 and KM-483

KM-J-26958-A             Measuring Device

       To adjust end play on turbine shaft

KM-J-28535        Checking Tool

       To check brake band assembly adjustment

KM-J-28540        Installer

       To drive in torque converter housing seal ring

KM-J-28542        Remover/Installer

       To remove and install reverse clutch

KM-J-28544        Checking Device

       To measure axial play of turbine shaft in conjunction with MKM-572 (or KM-J-8001 or commercially available measuring gauge) and Indicator Bolt KM-482

KM-J-28545        Remover/Installer

       To remove and install axle drive

KM-J-28583-A    Remover

       To remove snap ring from axle drive

KM-J-28585        Remover/Installer

       To remove snap ring on slow and reverse clutch

KM-J-28588        Gauge Set

       To measure end play in selector snap ring in conjunction with KM-482 and MKM-572 (or KM-J-8001)

KM-J-28630        Installer

       To drive in seal for slow and reverse clutch and to drive out cup-shaped plug

KM-J-28677        Installer

       To press new needle bearing into drive sprocket support in conjunction with KM-J-8092

KM-J-28698        Remover/Installer

       To press pump shaft bearing in and out in conjunction with drift of KM-305 and to drive new cup-shaped plug in flush

KM-J-29023        Height Gauge

       To check height when installing thermostat element

KM-J-29569        Seal Installer

       To mount both seal rings on short shank of turbine shaft

KM-J-29829        Installer

       To mount seal ring on long shank of turbine shaft