Wiring
Harness - Rear, Replace
Remove
Remove
cover for central plug connection on lower A pillar.
Remove
left hand sill inner trim panel.
Remove
luggage compartment covering and rear quarter inner trim panel.
Remove
covering for rear lamps.
Disconnect
wiring harness at socket of central plug connection from:
1 - Instrument panel wiring harness
2 - Wiring harness for central door locking system,
electric window operation and electric mirror adjustment
3 - Illumination for selector (only with auto.
transmission)
4 - Left hand turn signal lamp
5 - Right hand turn signal lamp
6 - Heating for right hand seat
7 - Heating for left hand seat
|
|
Unscrew
wiring harness from A pillar at socket of central plug connection.
Remove
door contact switch (only driver's door) and disconnect wiring harness.
A Door contact switch with headlamp "ON"
warning (special equipment)
B Door contact switch without headlamp
"ON" warning (grey cable attached to right angle plug).
|
|
Disconnect
following cables from wiring harness: when installing, reconnect to wiring
harness with clamp connectors:
1 - Door contact switch, passenger door (red)
2 - Interior lamp (grey)
3 - Parking brake monitoring switch (brown/white)
4 - Fuel gauge (blue/black:
ground
cable brown
0.75
mm/0.03 in.)
On
estates also
- Elec. fuel pump (blue: ground cable brown )
1.5
mm/0.06 in.)
On vehicles with RHD also:
5 - Disconnect wiring harness
from
radio wiring harness
at
plug connection.
|
|
Saloon
(Hatchback):
Remove
contact plate, tail gate
contact
switch, rear compartment lamp switch and license plate lamp (only LHD) and
disconnect wiring harness from each of them.
Disconnect
wiring harness from:
- Rear lamps
- Electric fuel pump (only GSI/GTE)
Unscrew
ground cable from tail gate.
Disconnect
wiring harness at plug connections from:
- Cable for rear compartment lamp
- Wiring harness for trailer hitch if fitted
On
vehicles with RHD also:
- Disconnect wiring harness from all loudspeakers.
- Disconnect wiring harness at plug connection from
bumper wiring harness.
Pull
wiring harness with rubber grommets into rear of passenger compartment.
Install
(Saloon - Hatchback)
Analogously
in reverse order.
Saloon
(Notchback):
Remove
license plate lamp and disconnect wiring harness.
Remove
luggage compartment inner panelling and disconnect wiring harness from:
- Rear lamps
- Electr. fuel pump (only C 18 NT, NE engines)
Unscrew
ground cable from rear end panel.
Disconnect
wiring harness from:
- Luggage compartment light if present
- Contact switch for luggage compartment light if
present
- Wiring harness for motor for central locking
system (luggage compartment lid) - if present
- Cable for heated rear screen
- Wiring harness for trailer operation - if
present.
Pull
wiring harness with rubber grommets into vehicle.
Install
(Saloon - Notchback):
Analogously
in reverse order.
|
|
Estate:
On
vehicles with LHD, remove license plate lamps and disconnect wiring harness.
Unscrew
ground cable from left hand lower D pillar.
Disconnect
wiring harness from rear lamps.
Disconnect
wiring harness at plug connections from:
- Cable for rear compartment lamp
- Tail gate wiring harness
- Trailer hitch wiring harness if fitted.
On
vehicles with RHD also:
- Disconnect wiring harness from all loudspeakers
- Disconnect wiring harness at plug connection
from bumper wiring harness.
Pull
wiring harness and rubber grommets into rear of passenger compartment.
Install
(Estate)
Analogously
in reverse order.
|
|