A2
Subframe (basic running gear): exploded view |
General notes → Chapter |
1 - | Subframe |
q | Removing and installing → Chapter |
q | Different versions: Vehicles with petrol engine have a recess on the underside -arrow- |
q | For correct version refer to → Parts catalogue |
2 - | Hexagon nut, 40 Nm |
3 - | Anti-roll bar |
q | Removing and installing → Chapter |
4 - | Rubber bush |
5 - | Clamp |
6 - | Hexagon nut, 40 Nm |
q | Always renew if removed |
7 - | Coupling rod (link between anti-roll bar and suspension strut) |
8 - | Suspension bracket |
q | On subframe |
9 - | Hexagon bolt M12 x 1.5 x 75 |
q | 70 Nm and turn 90° further |
q | Always renew if removed |
10 - | Bonded rubber bush for suspension bracket |
q | Removing and installing → Chapter |
q | Pressing in and out with -V.A.G 1459 B- → Chapter |
11 - | Hexagon nut |
q | 20 Nm and turn 90° further |
q | Always renew if removed |
12 - | Wishbone with swivel joint |
q | Forged steel version |
q | For correct version refer to → Parts catalogue |
q | Removing and installing → Chapter |
q | Renew wishbone if swivel joint is defective |
q | Supplied only as complete assembly with front stop washer, front bush and rear stop washer |
q | Renew wishbone if bonded rubber bush is damaged |
q | Must not be installed together with wishbone → Item on same vehicle |
13 - | Hexagon nut |
q | 20 Nm and turn 90° further |
q | Always renew if removed |
14 - | Swivel joint |
q | Checking → Chapter |
q | Removing and installing → Chapter |
15 - | Hexagon bolt |
q | 20 Nm and turn 90° further |
q | Always renew if removed |
q | Note required sequence when installing bolts: |
1. | Start threads of all bolts. |
2. | Tighten centre bolt to specified torque. |
3. | Tighten the two outer bolts to specified torque. |
16 - | Wishbone |
q | Fabricated version consisting of welded sheet-metal sections with welded-on mountings for suspension bushes |
q | For correct version refer to → Parts catalogue |
q | Removing and installing → Chapter |
q | Supplied only as complete assembly with front stop washer, bush and rear stop washer |
q | Renew wishbone if bonded rubber bush is damaged |
q | Must not be installed together with wishbone + swivel joint → Item on same vehicle |
17 - | Locking plate with nuts |
q | Always renew if removed |
18 - | Hexagon bolt |
q | 20 Nm and turn 90° further |
q | Always renew if removed |
19 - | Hexagon bolt, 50 Nm |
q | Always renew if removed |
20 - | Hexagon bolt |
q | 50 Nm and turn 90° further |
q | Always renew if removed |
21 - | Hexagon bolt |
q | 40 Nm and turn 90° further |
q | Always renew if removed |
22 - | Hexagon bolt M12 x 1.5 x 100 |
q | 70 Nm and turn 90° further |
q | Always renew if removed |
q | Note required assembly sequence: |
– | First tighten hexagon bolt → Item lightly, then tighten hexagon bolt → Item lightly. |
– | Then tighten hexagon bolts alternately to specified torque. |
23 - | Hexagon bolt |
q | 4x |
q | 50 Nm and turn 90° further |
q | Always renew if removed |
q | Note required assembly sequence: |
q | First tighten hexagon bolt → Item lightly, then tighten hexagon bolt → Item lightly. |
q | Then tighten hexagon bolts alternately to specified torque. |
24 - | Retaining plate |
q | For correct version refer to → Parts catalogue |
25 - | Hexagon nut |
26 - | Pendulum support |