Audi Workshop Service and Repair Manuals

Exploded view - gear selector cable and gate selector cable from model year 2008 onwards

Lubricate all bearings and moving surfaces with grease -G 000 450 02-.

1 -	Selector mechanism cover

2 -	Slide block

3 -	Relay lever

q	Made of plastic

q	Different versions available; for correct version refer to → Electronic parts catalogue

q	Installation position → Fig.

q	Detaching and securing relay lever (with detent catch) at selector mechanism cover → Fig.

q	Detaching and securing relay lever (with clip) at selector mechanism cover → Fig.

4 -	Cable end-piece

q	Secures gate selector cable to relay lever

q	Allocation → Fig.

q	Detaching from gate selector cable → Fig.

5 -	Gearbox selector lever

q	With damper weight

q	Fitting → Fig.

q	Installation position → Fig.

q	After installing, adjust selector mechanism → Chapter

6 -

Nut

q	Self-locking

q

Renew

q

23 Nm

7 -	Cable end-piece

q	Secures gear selector cable to gearbox selector lever

q	Allocation → Fig.

q	Detaching from gear selector cable → Fig.

8 -	Securing clip

q	Removing → Fig.

q

Renew

9 -	Retaining clips

q

Renew

10 -	Gate selector cable

q	Removing and installing → Chapter

q	Adjusting → Chapter

q	Secure to gear selector cable with cable tie → Fig.

11 -	Selector housing

12 -	Retaining clips

q

Renew

13 -	Gear selector cable

q	Detaching and securing at gearbox selector lever → Fig.

q	Removing and installing → Chapter

q	Adjusting → Chapter

q	Secure to gate selector cable with cable tie → Fig.

14 -	Cable support bracket

15 -

Bolt

q

20 Nm

16 -

Grommet

17 -

Bush

18 -

Oil seal

q	For selector shaft

q	Renewing → Fig.

19 -

Clip

q	For relay lever (only from 08.2008 onwards)

Identification of cable end-pieces The holes in the cable end-pieces have different diameters.

Cable end-piece for:	Dimension „a“
-1- Gear selector cable to gearbox selector lever	8.5 mm
-2- Gate selector cable to relay lever	10 mm

Installing gearbox selector lever –  When installing gearbox selector lever, make sure that the gap in the splines -arrow A- aligns with the wider spline -arrow B- on the selector shaft.

Installation position: gearbox selector lever/relay lever 1 -  Gearbox selector lever  -  With damper weight 2 -  Relay lever  -  Locates in guide rail of gearbox selector lever via slide block -arrow-.

Detaching cable end-pieces from gear selector cable and gate selector cable –  Pull locking mechanism forwards -arrow 1- onto stop and then turn in direction of -arrow 2- to lock. –  Take cable -B- out of cable end-piece -A-.

Detaching and securing gear selector cable at gearbox selector lever Detaching –  Lift up tab and detach securing clip -1- for gear selector cable from gearbox selector lever -2-. –  Pull gear selector cable off pin -arrow-. Securing   Note t  Renew securing clip for gear selector cable. t  Apply a small amount of grease -G 000 450 02- to pin -arrow-. –  Push gear selector cable onto gearbox selector lever -2- and secure with securing clip -1-.

Detaching and securing relay lever (with detent catch) at gearbox selector lever (selector mechanism cover) Detaching –  Press detent -arrow 1- down onto stop and remove relay lever together with cable end-piece. Move relay lever in normal direction of operation.   Note -Arrow 2- can be disregarded. Securing   Note To install, lubricate bearings and moving surfaces with grease -G 000 450 02-. –  Press cable end-piece onto relay lever → Fig.. –  Insert relay lever with cable end-piece as far as stop. l  Relay lever is secured by detent -arrow 1-. l  Cable end-piece is secured by detent -arrow 2-. l  Ensure that components engage securely.

Detaching and securing relay lever (with clip) at gearbox selector lever (selector mechanism cover) Detaching –  Remove clip -arrow 1- and take off relay lever together with cable end-piece. Securing   Note Lubricate all bearings and moving surfaces with grease -G 000 450 02-. –  Insert relay lever with cable end-piece as far as stop. –  Press on clip -arrow 1-, making sure it engages securely.   Note -Arrow 2- can be disregarded.

Levering cable end-piece for gate selector cable off relay lever l  Relay lever removed –  Apply plain slot screwdriver -A- between bush -B- and relay lever.

Pressing cable end-piece for gate selector cable onto relay lever l  Relay lever removed l  Press on cable end-piece only at bush -arrow-. l  Cable end-piece must move freely on relay lever. l  Cable end-piece must be behind detent. –  Ensure that components engage securely.

Position of cable tie securing selector cables –  Wrap cable tie round selector cables in a „figure-of-eight“-arrow- and secure cable tie as shown in illustration.