chevrolet Workshop Repair Guides

Chevrolet Workshop Service and Repair Manuals

Deployment Procedures|Page 8406 > < Deployment Procedures|Page 8404
Page 5
background image

42. Discard both deployment harnesses.
43. After deploying both air bags, you may scrap the vehicle in the same manner as a non-SIR equipped vehicle.
44. In the unlikely event that the inflatable restraint steering wheel module did not deploy after following these procedures, proceed immediately with

Steps 44-46.

45. Remove the undeployed inflator module(s) from the vehicle. For the inflatable restraint steering wheel module, refer to Supplemental Inflatable

Restraint (SIR) Steering Wheel and Column in Steering. For the inflatable restraint IP module, refer to Infl Rst Instrument Panel Module
Replacement.

CAUTION:  When you are carrying an undeployed inflator module:

^

Do not carry the inflator module by the wires or connector on the inflator module

^

Make sure the bag opening points away from you

When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator
module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical.
Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.

46. Temporarily store the inflator module with its vinyl trim cover facing up.
47. Call the Technical Assistance group for further assistance.

Inflatable Restraint Steering Wheel Module

Tools Required

J 38826 SIR Deployment Harness

When you intend to return the vehicle to service, deploy the inflator modules outside of the vehicle. Consider the following examples:

^

Using the SIR Diagnostics, you determine that the inflator module does not function correctly.

^

The inflator module is cosmetically damaged, such as a scratch or a rip in the cover.

^

The inflator module pigtail (if equipped) is damaged.

^

The inflator module connector is damaged.

^

An inflator module connector terminal is damaged.

Deployment and disposal of a malfunctioning inflator module is subject to any required retention period. You must follow these inflator module
deployment procedures exactly. Always wear safety glasses during this deployment procedure. Do not remove your safety glasses until the deployed
inflator module is scrapped or shipped. Before performing theses deployment procedures, you should be familiar with servicing the SIR system. You
should also know how to handle the inflator module properly. Read the procedures carefully before you begin. These procedures require the use of the
following tools:

^

J 38826 SIR Deployment Harness

^

The appropriate pigtail adapter

Do not attempt the procedure without the J 38826 SIR Deployment Harness and the adapter.

CAUTION:  When you are deploying an inflator module for disposal, perform the deployment procedures in the order listed. Failure to follow
the procedures in the order listed may result in personal injury.

IMPORTANT:  This information applies only to inflatable restraint steering wheel modules. Refer to Deployment Outside of the Vehicle (Inflatable
Restraint IP Module) for information on inflatable restraint IP module scrapping.

1. Turn the ignition switch to the LOCK position.
2. Remove the key.
3. Put on safety glasses.
4. Inspect the J 38826 SIR Deployment Harness and the appropriate pigtail adapter for damage. If either the harness or the adapter is damaged,

obtain a replacement.

5. Short the two SIR deployment harness leads together by fully seating one banana plug into the other, as shown in the figure.

^

Keep the SIR deployment harness (1) shorted until you are ready to deploy the air bag.

^

Do not connect the SIR deployment harness to a power source until you are ready to deploy the air bag.

6. Connect the appropriate pigtail adapter (2) to the SIR deployment harness.
7. Remove the inflatable restraint steering wheel module from the vehicle. Refer to Supplemental Inflatable Restraint (SIR) Steering Wheel and

Column in Steering.

8. Remove the horn lead from the back of the inflatable restraint steering wheel module, if applicable.
9. Remove the redundant steering wheel control lead(s) from the back of the inflatable restraint steering wheel module, if applicable.

Deployment Procedures|Page 8406 > < Deployment Procedures|Page 8404