| Specifications Wheel Alignment (at kerb weight) - Castor and Camber | All saloon, wagon and cabriolet | Degrees and Minutes | 1°12" | 2° 32" to -0° 08" | -0°19" | 1° 05" to -1° 43" | | All 4 x 4 | Degrees and Minutes | 1° 23" | 2° 48" to 0° 03" | -0° 21" | 1° 03" to -1° 45" | | All van | Degrees and Minutes | 0° 37" | 1° 57" to -0° 43" | -0° 23" | 1° 01" to -1° 47" | | All saloon, wagon and cabriolet | Decimal Degrees | 1,20° | 2,53° to -0,13° | -0,32° | 1,08° to -1,72° | | All 4 x 4 | Decimal Degrees | 1,38° | 2,71° to 0,05° | -0,35° | 1,05° to -1,75° | | All van | Decimal Degrees | 0,61° | 1,94° to -0,72° | -0,38° | 1,02° to -1,78° | | Maximum variation - left to right‐hand side - Castor 1°00" (1,00°) Camber 1°15" (1,25°) | Wheel Alignment (at kerb weight) - Toe Setting - All Variants | -0,5 mm (Toe‐out) to 4,5 mm (Toe‐in) | 2,0 mm (Toe‐in) ± 1,0 mm | | -0°05" (Toe‐out) to 0°45" (Toe‐in) | 0°20" (Toe‐in ) 0°10" | | -0,09° (Toe‐out) to 0,78° (Toe‐in) | 0,35° (Toe‐in ) ± 0,17° | Lubricants, Fluids, Sealers and Adhesives | Power steering fluid | ESPM‐2C166‐H | | Track rod locknuts | 63 | 46 | | Lower arm retaining nuts and bolts | 50 +90° | 50 +90° | | Fuel filter bracket retaining bolts | 23 | 17 | | Stabiliser bar retaining bolts | 24 | 18 | | Steering gear retaining bolts | 15 +90° | 15 +90° | | Subframe retaining bolts | 85 | 63 | | Steering gear pipe clamp plate bolt (TRW steering gear) | 22 | 16 | | Steering gear pipe unions (Wuelfrath steering gear) | 31 | 23 | | Connecting link to suspension unit retaining nut | 50 | 37 | | Connecting link to stabiliser bar retaining nut | 50 | 37 | | Engine/transmission lower mounting bolt | 68 | 50 | | Engine support bar bolt | 84 | 62 | | Lower arm to spindle carrier pinch bolt and nut | 54 | 40 | | Track rod end castellated nut | 28 | 21 | | Track rod end nyloc nut | 50 | 37 | | Manual gear change linkage retaining bolts | 23 | 17 | | Engine/transmission upper mounting bolt | 68 | 50 | | Flexible coupling to pinion shaft pinch bolt | 23 | 17 | | Wheel nuts | 85 | 63 | | Spindle carrier to suspension unit pinch bolt | 85 | 63 | | Wheel sensor retaining bolt | 10 | 7 | | Caliper assembly retaining bolts | 58 | 43 | | Suspension unit top mount retaining nuts (two) | 46 | 34 | | Suspension unit top mount retaining nuts (three) | 34 | 25 | | Hub retaining nut | 235 | 173 | | Brake hose bracket to suspension unit retaining nut | 44 | 32 | | Suspension unit top mount nut | 58 | 43 | | Catalytic converter nuts | 40 | 30 | | Engine roll restrictor bolt | 84 | 62 | |
