Lubricants, Fluids, Sealers and Adhesives | Item | Specification | | Automatic transmission fluid | WSS-M2C202-B | | Sealer, transmission housing | SQM-4G9523-A | | Vaseline | SM-1C115-A | Capacities | | Litres | | Automatic transmission (with oil cooler) | 5,0 | Oil cooler | | | Twin pipe oil cooler in engine radiator water tank | | The diameter of the oil cooler feed and return pipes is 10 mm | | An additional oil cooler is connected in line with the oil cooler in the engine radiator water tank | Measuring and Adjusting Shims (in mm) | Description | Input shaft | Differential | Reduction Gear | | Measuring shim | - | 3,80 | 2,10 | | Adjusting shim availability | 0,75 - 2,08 | 0,06, 0,10, 0,20 | 2,06 - 3,06 | | | (in steps of 0,08 mm) | 4,2, 4,6, 5,0 | (in steps of 0,04 mm) | Bearing pre-load | Description | mm | | Differential | 0,30 | | Reduction gear | 0,02 - 0,07 | | (desirable value) | 0,05 | Transmission Ratios | Description | Ratio | Number of teeth | | Reduction Gear | 1,48 | 23 / 34 | | Differential | 3,842 | 19 / 73 | | Steel belt (slow) | 2,60 | | | Steel belt (fast) | 0,45 | | | Whole transmission (slow) | 14,77 | | | Whole transmission (fast) | 2,53 | | Speedometer Drive | Description | Number of teeth | | Speedometer drive worm wheel | 21 | | Speedometer drive pinion | 19 | Torque Specifications | Description | Nm | lb-ft | lb-in | | Suspension strut nut | 45 | 33 | - | | Transmission to engine | 44 | 32 | - | | Starter motor to transmission | 44 | 32 | - | | Suspension arm to spindle carrier | 52 | 38 | - | | Transmission drain plug | 33 | 24 | - | | Engine mounting bracket bolt | 55 | 41 | - | | Exhaust flange bolt | 47 | 35 | - | | Center bearing to bracket | 24 | 18 | - | | Engine roll restrictor to engine | 50 | 37 | - | | Engine roll restrictor to front axle | 70 | 52 | - | | Starter motor bracket to engine block | 24 | 18 | - | | Battery plus cable to starter motor | 11 | 8 | - | | Battery cable to starter | 6 | 4 | 53 | | Exhaust to flexible exhaust tube | 47 | 35 | - | | Power steering pump to cylinder block | 23 | 17 | - | | Radiator crossmember | 25 | 18 | - | | Transmission fluid lines to transmission | 22 | 16 | - | | Front engine mounting bracket | 69 | 51 | - | | Rear engine mounting bracket nuts | 69 | 51 | - | | Rear engine mounting bracket bolts | 49 | 36 | - | | Battery compartment bolts | 25 | 18 | - | Torque Specifications | Description | Nm | lb-ft | lb-in | | Housing cover - secondary cover | 24 | 18 | - | | Oil pan | 8 | 6 | 71 | | Oil strainer | 8 | 6 | 71 | | Valve body to transmission, 1st stage | 5 | 2 | 44 | | Valve body to transmission, 2nd stage | 8 | 6 | 71 | | Connector to transmission | 24 | 18 | - | | Transmission fluid line to transmission | 22 | 16 | - | | Transmission fluid line to radiator | 22 | 16 | - | | Oil pump to transmission | 10 | 7 | 89 | | Oil spray tube | 8 | 6 | 71 | | Engine pitot tube bolt | 10 | 7 | 89 | | Engine pitot chamber | 8 | 6 | 71 | | Primary pitot chamber (transmission pitot) | 8 | 6 | 71 | | Crown wheel to differential cage (six hole) | 115 | 85 | - | | Crown wheel to differential cage (eight hole) | 85 | 63 | - | | Reduction gear bearing cap | 39 | 29 | - | | Nut - primary unit | 210 | 155 | - | | Nut - secondary unit | 210 | 155 | - | | Selector shaft retaining bolt | 23 | 17 | - | | Grid to selector shaft | 17 | 13 | - | | Primary unit blanking cover | 10 | 7 | 89 | | Pressure gauge connection blanking plug | 17 | 13 | - | | Transmission housing bolts | 24 | 18 | - | | Start inhibitor switch | 12 | 9 | - | Torque Specifications | Description | Nm | lb-ft | lb-in | | Selector lever housing to floor assembly | 11 | 8 | - | | Transmission selector lever | 17 | 13 | - | | |
