Engine Data - 100 PS
Description | |
Code | FFBA |
Emission level | Stage IV |
Firing order | 1-3-4-2 |
Bore diameter | 82.5 mm |
Stroke | 82 mm |
Displacement | 1753 cc |
Compression ratio | 19.4 : 1 |
Power output at 4000 rpm | 74 kW (100 PS) |
Torque at 2000 rpm | 250 Nm |
Idle speed | 900 rpm |
Maximum oil consumption | 0.1L/1000km |
Engine Data - 125 PS
Description | |
Code | QYBA |
Emission level | Stage IV |
Firing order | 1-3-4-2 |
Bore diameter | 82.5 mm |
Stroke | 82 mm |
Displacement | 1753 cc |
Compression ratio | 19.4 : 1 |
Power output at 4000 rpm | 92 kW (125 PS) |
Torque at 2000 rpm | 250 Nm |
Idle speed | 900 rpm |
Maximum oil consumption | 0.1L/1000km |
Engine Oil Capacity
Description | Liters |
Initial fill including oil filter | 6.1 |
Service fill including oil filter | 5.6 |
Service fill without oil filter | 5.0 |
Cylinder Block Dimensions
Description | mm |
Cylinder bore diameter — Class 1 | 82.500 - 82.515 |
Cylinder bore diameter — Class 2 | 82.515 - 82.530 |
Main bearing parent bore diameter | 57.683 - 57.696 |
Piston Dimensions
Description | mm |
Piston diameter — Class 1 | 82.410 - 82.425 |
Piston diameter — Class 2 | 82.425 - 82.440 |
Piston ring end gaps | |
— upper compression ring | 0.200 - 0.300 |
— lower compression ring | 0.350 - 0.550 |
— oil control ring | 0.250 - 0.450 |
Piston ring gap position: The piston ring gaps must be distributed evenly around the circumference of the piston. This also applies to the oil control ring elements. Align the piston ring gaps at 120 degrees to each other.
Crankshaft Dimensions
Description | mm |
Main bearing journal end float | 0.110 - 0.370 |
Main bearing journal diameter | 53.970 - 53.990 |
Connecting rod bearing journal diameter | 49.024 - 49.046 |
Connecting Rod Dimensions
Description | mm |
Large end bore diameter | 52.000 - 52.020 |
Small end bore diameter | 26.815 - 26.885 |
Connecting rod bearing radial clearance | 0.025 - 0.085 |
Piston Pin Dimensions
Description | mm |
Piston pin diameter | 28.004 - 28.010 |
Camshaft Dimensions
Description | mm |
Camshaft end float | 0.100 - 0.240 |
Camshaft bearing journal diameter | 27.960 - 27.980 |
Cylinder Head Dimensions
Description | mm |
Valve guide inner diameter | 8.000 - 8.025 |
| |
Intake valve clearance | 0.300 - 0.400 |
Exhaust valve clearance | 0.450 - 0.550 |
Camshaft bearing parent bore diameter | 30.500 - 30.525 |
Maximum distortion — measured longitudinally and diagonally | 0.600 |
Thickness of cylinder head gasket with piston protrusion of 0.550 mm - 0.600 mm | 1.270 (two tooth marks) |
Thickness of cylinder head gasket with piston protrusion of 0.601 mm - 0.650 mm | 1.320 (three tooth marks) |
Thickness of cylinder head gasket with piston protrusion of 0.651 mm - 0.700 mm | 1.370 (four tooth marks) |
Thickness of cylinder head gasket with piston protrusion of 0.701 mm - 0.750 mm | 1.420 (five tooth marks) |
Thickness of cylinder head gasket with piston protrusion of 0.751 mm - 0.800 mm | 1.470 (six tooth marks) |
Thickness of cylinder head gasket with piston protrusion of 0.801 mm - 0.850 mm | 1.520 (seven tooth marks) |
Lubricants, Fluids, Sealers and Adhesives
Item | Specification |
Engine oil | WSS-M2C913-B |
Coolant | WSS-M97B44-D |
Sealant | WSE-M4G323-A4 |
Oil Pressure Specifications
Description | bar |
Minimum oil pressure at idle speed | 0.54 |
Minimum oil pressure at 2000 rpm | 1.39 |