Hombre XS Space Cab 2WD V6-4.3L (1998)
43. Remove the drop cloth from the vehicle.
44. Disconnect both harnesses from the vehicle.
45. Discard the harnesses.
46. Scrap the vehicle in the same manner as a non-SRS equipped vehicle.
47. If one or both of the modules did not deploy, perform the following steps:
47.1.
Remove the undeployed module(s) from the vehicle.
47.2.
Temporarily store the module(s).
47.3.
Call the Technical Assistance Group for further assistance.
Handling a Deployed Supplemental Restraint Steering Wheel Inflator Module
After the inflator module has deployed, the surface of the air bag may contain a powdery residue. This powder consists primarily of cornstarch (used to
lubricate the bag as it inflates), and by-products of the chemical reaction. The deployment reaction produces sodium hydroxide dust (similar to lye soap).
The sodium hydroxide quickly reacts with the atmospheric moisture. This atmospheric moisture converts the sodium hydroxide into sodium carbonate
and sodium bicarbonate (baking soda). Therefore, you will probably find no sodium hydroxide present after the deployment. Gloves and safety glasses
are recommended, however, as a precaution. Gloves and safety glasses help to prevent possible irritation of the skin or eyes.
Airbag Deployment and Disposal (Outside Vehicle)
Deployment Outside Vehicle (Supplemental Restraint IP Module)
Dealers should refer to the latest Service Bulletins for live (undeployed) supplemental restraint IP module scrapping and disposal procedures. All others
should contact a local dealer for these procedures. Dispose of deployed IP modules through normal refuse channels.
Deployed Air Bag Handling
When handling a deployed air bag assembly, a face shield and rubber gloves should be worn. Vehicle interior and A/C, vent, defroster and heater ducts
should be vacuumed. If sinus or throat irritation is encountered during air bag removal, exit vehicle and breathe fresh air. If skin irritation is encountered,
flush effected area with cool water. If sinus, throat, skin or any other type of irritation continues, consult a physician. After handling a deployed air bag
assembly, wash hands and rinse thoroughly with water.
An air bag that has been deployed should be removed from the vehicle. Prior to removing a deployed air bag assembly, place tape over air bag exhaust
vents. After unit has been removed, it should be placed in a heavy duty plastic bag and sealed securely. The sealed plastic bag should then be placed with
automotive scrap. An air bag assembly that has not been deployed, must be deployed prior to disposal.
Put on a pair of shop gloves and safety glasses to protect your hands and eyes from possible irritation and heat when handling the deployed air bag
assembly.
After the air bag assembly has been deployed, the surface of the air bag may contain a powdery residue. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by products of the chemical reaction. Sodium hydroxide dust (similar to lye soap) is produced as a by product
of the deployment reaction. The sodium hydroxide then quickly reacts with atmospheric moisture and is converted to sodium carbonate and sodium
bicarbonate (baking soda).
Driver Airbag Assembly
After the air bag assembly has been deployed, the surface of the air bag may contain a powdery residue. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by products of the chemical reaction. Sodium hydroxide dust (similar to lye soap) is produced as a by product
of the deployment reaction. The sodium hydroxide then quickly reacts with atmospheric moisture and is converted to sodium carbonate and sodium
bicarbonate (baking soda). Therefore, it is unlikely that sodium hydroxide will be present after deployment.
Passenger Airbag Assembly
The passenger inflator requires no special precaution after deployment. 95% of the particulate emission are potassium chloride (KCL), which is
commonly sold as an edible salt-substitutes. even if water is applied. Post deployment products are relatively pH neutral. Disposing the inflator by
burying it in a landfill will not products any hazardous products. As with any dusty environment, safety goggles, dust mask and gloves should be worn.
Damaged Airbag/Tensioner Special Procedure
WARNING: If an airbag (or Seat Belt Tensioner) cannot be deployed, it should not be treated as normal scrap; it should still be considered a
potentially explosive device that can cause serious injury.
Special Procedure For Damaged Airbag
1. If installed in a vehicle, follow the removal procedure.
2. In all cases, make a short circuit by twisting together the two airbag inflator wires.
3. Package the airbag in exactly the same packaging that the new replacement part came in.