L322 Range Rover Service Procedures
ENGINE - V8
12-2-44 REPAIRS
37. Fit new 'O' ring to PAS hose union, connect
hose to pump and tighten nut to 25 Nm (18
lbf.ft).
38. Connect supply hose to PAS pump and secure
using new clip.
39. Fit oil filter housing to bracket and tighten
securing nuts.
40. Connect multiplug to oil pressure switch.
41. Connect SAI control valve hoses.
42. Fit new 'O' rings to A/C pipes and lubricate with
clean refrigerant oil.
43. Align A/C pipes to condenser and compressor.
Fit Allen bolts securing A/C pipes to condenser
and compressor and tighten to 25 Nm (18
lbf.ft).
44. Connect multiplug to A/C compressor.
45. Connect coolant hose to 'T' junction and secure
clip.
46. Fit radiator top hose and secure with clips.
47. Fit radiator bottom hose, secure with clips and
tighten 'P' clip securing bolt.
48. Connect multiplug to radiator bottom hose.
49. Connect vacuum pipe to inlet manifold.
50. Connect brake vacuum servo hose to 1 way
valve and secure using new clip.
51. Clean fuel hose connections.
52. Connect fuel feed hose to fuel rail.
53. Connect multiplug to starter motor lead.
54. Position gearbox multiplug and bracket to bell
housing and tighten securing bolt.
55. Connect heater hoses to coolant manifold and
secure with clips.
56. Fit transmission breather pipes into clips.
57. Fit charcoal canister purge valve pipe.
58. Position engine harness to engine.
59. Connect multiplug to charcoal canister purge
control valve.
60. Fit washer to fuel injector harness securing
stud.
61. Position and secure engine harness to brackets
with clips.
62. Connect multiplugs to RH fuel injectors.
63. Connect multiplugs to LH fuel injectors.
64. Connect alternator harness to 2 clips on engine
cover mounting brackets.
65. Fit fuel hose and mounting bracket to LH fuel
injector harness securing stud.
66. Fit vacuum reservoir and mounting bracket to
LH fuel injector harness securing stud.
67. Fit 2 nuts securing fuel injector harness to
induction manifold and tighten nuts.
68. Connect multiplugs to knock sensors.
69. Connect multiplugs to CMP sensors.
70. Secure alternator harness into 4 securing clips.
71. Connect multiplug to alternator.
72. Connect multiplug to SAI control valve.
73. Connect multiplugs to VCC solenoids.
74. Connect multiplugs to throttle body, thermostat
heater, ECT sensor, and RH CMP sensor.
75. Align engine harness to throttle body and
secure using new cable ties.
76. Connect multiplugs to ignition coils.
77. Connect engine harness earth leads to LH and
RH camshaft covers and tighten nuts.
78. Position differential breather pipe to LH engine
camshaft cover.
79. Fit LH ignition coil cover.
V8, REPAIRS, Cover - Ignition coils - LH.
80. Fit RH ignition coil cover.
V8, REPAIRS, Cover - Ignition coils - RH.
81. Fit viscous coupling.
82. Fit front road wheels and tighten nuts to 140
Nm (103 lbf.ft).
83. Remove stands and lower front end of vehicle.
84. Fit MAF/IAT sensor.
V8, REPAIRS, Sensor - combined mass air
flow (MAFS) & intake air temperature (IAT).
85. Recharge A/C system.
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
86. Fit air intake plenum.
87. Fit battery positive lead to stud, tighten nut to 18
Nm (13 lbf.ft) and close cover.
88. Connect battery earth lead.
89. Fill cooling system.
ADJUSTMENTS, Coolant - drain, flush &
refill.
90. Bleed PAS system.
assisted steering (PAS) system - bleed.
91. Connect support stays and close bonnet.
