HS 250h L4-2.4L (2AZ-FXE) Hybrid (2010)
without SST - Torque : 18 Nm (178 kgf-cm, 13 ft-lbf)
with SST - Torque : 11 Nm (112 kgf-cm, 8 ft-lbf)
NOTICE:
*
Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
*
This torque value is effective when SST is parallel to a torque wrench.
*
If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector,
replace it with a new one.
*
When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched
between other parts.
*
When the power switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is
in the vehicle.
(d) Connect the connectors to the center airbag sensor assembly as shown in the illustration.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
(e) Check that the waterproof sheet is properly set.
(f) Check that there is no looseness in the installation parts of the center airbag sensor assembly.
2. INSTALL REAR NO. 2 AIR DUCT
(a) Engage the 6 claws to install the rear No. 2 air duct.
3. INSTALL NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY See: Brakes and Traction Control/Parking Brake System/Parking
Brake Pedal/Service and Repair/Removal and Replacement/Installation
4. INSTALL NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY See: Brakes and Traction Control/Parking Brake System/Parking
Brake Pedal/Service and Repair/Removal and Replacement/Installation
5. INSTALL COOLER BLOWER ASSEMBLY See: Heating and Air Conditioning/Blower Motor/Service and Repair/Removal and
Replacement/Blower Unit (for Rear Side)/Installation
6. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET See: Heating and Air Conditioning/Blower Motor/Service and Repair/Removal and
Replacement/Blower Unit (for Rear Side)/Installation
7. INSTALL NO. 4 CONSOLE BOX DUCT See: Heating and Air Conditioning/Blower Motor/Service and Repair/Removal and
Replacement/Blower Unit (for Rear Side)/Installation
8. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal and Replacement/Lower Instrument Panel/Installation
9. INSTALL CONSOLE BOX See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal and
Replacement/Upper Instrument Panel/Installation
10. INSTALL CONSOLE BOX LH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal and
Replacement/Upper Instrument Panel/Installation
11. INSTALL CONSOLE BOX RH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal and
Replacement/Upper Instrument Panel/Installation
12. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Console/Service and Repair/Removal and
Replacement/Installation
13. INSTALL CONSOLE BOX CARPET See: Body and Frame/Interior Moulding / Trim/Console/Service and Repair/Removal and
Replacement/Installation
14. INSTALL REAR CONSOLE PANEL SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Console/Service and Repair/Removal
and Replacement/Installation
15. INSTALL FRONT CONSOLE UPPER PANEL GARNISH (w/o Seat Heater System) See: Body and Frame/Interior Moulding /
Trim/Console/Service and Repair/Removal and Replacement/Installation