Lancer L4-2.4L SOHC (2005)
PROM - Programmable Read Only Memory: All Technical Service Bulletins
Engine Controls - MIL ON/DTC P2100/P2138/P0736/P1784
No: TSB-06-13-011REV
DATE: August, 2006
MODEL: See below
SUBJECT:
PCM REPROGRAMMING FOR DTC
P2100 / P2138 / P0736 (46 / P1784)
SUBJECT:
PCM REPROGRAMMING FOR DTC
P2100 / P2138 / P0736 (46 / P1784)
This bulletin superseded TSB-06-13-011, to add Eclipse, Endeavor, Galant and Outlander models and to add automatic transmission codes 46 and
P1784. Revisions are indicated by -->.
PURPOSE
On some affected vehicles, incorrect software parameters in the PCM may cause the MIL to illuminate and Diagnostic Trouble Code P2100 (Throttle
Actuator Control Motor Circuit), P2138 (Accelerator Pedal Position Sensor (main and sub) Range/Performance Problem) or P0736 Reverse Gear
--> Incorrect Ratio) to set in the PCM. Automatic transmission Diagnostic Trouble Codes 46 (Reverse Gear Incorrect Ratio) or P1784 (Reverse Gear
Incorrect Ratio) may also be stored in the PCM. To eliminate this condition, reprogram the PCM as described in this bulletin.
--> AFFECTED VEHICLES
2006 Eclipse 2.4L MIVEC M/T for DTC P2100 and P2138
2006 Eclipse 2.4L MIVEC A/T for DTC P2100, P2138 and P0736 (A/T code P1784)
2006 Eclipse 3.8L M/T for DTC P2100 and P2138
2006 Eclipse 3.8L A/T for DTC P2100, P2138 and P0736 (A/T code P1784)
2007 Eclipse/Eclipse Spyder 2.4L MIVEC M/T for DTC P2100 and P2138
2007 Eclipse Spyder 2.4L MIVEC A/T for DTC P2100, P2138 and P0736 (A/T code P1784)
2007 Eclipse 2.4L MIVEC A/T for DTC P2100, P2138 and P0736 (A/T code P1784)
2007 Eclipse/Eclipse Spyder 3.8L M/T for DTC P2100 and P2138
2007 Eclipse/Eclipse Spyder 3.8L A/T for DTC P2100, P2138 and P0736 (A/T code P1784)
2005-2006 Endeavor 2WD and AWD for DTC P2100, P2138 and P0736 (A/T code 46)
2005 Galant 2.4L MIVEC, California for DTC P2100, P2138 and P0736 (A/T code 46)
2005 Galant 3.8L for DTC P2100, P2138 and P0736 (A/T code 46)
2006 Galant 2.4L MIVEC, Federal for DTC P2100, P2138 and P0736 (A/T code P1784)
2006 Galant 2.4L MIVEC and 3.8L for DTC P2100, P2138 and P0736 (A/T code P1784)
2004-2006 Lancer and Lancer Sportback 2.4L MIVEC, A/T and M/T for DTC P2138
2005-2006 Lancer and Lancer Sportback 2.4L MIVEC, A/T for DTC P0736 (A/T code 46)
2006 Lancer and Lancer Sportback 2.4L MIVEC, A/T and M/T for DTC P2100
2004-2006 Outlander 2.4L MIVEC 2WD and AWD for DTC P2138
2005-2006 Outlander 2.4L MIVEC 2WD and AWD A/T for DTC P0736 (A/T code 46)
2006 Outlander 2.4L MIVEC 2WD and AWD for DTC P2100
PROCEDURE
CAUTION
BATTERY VOLTAGE (AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD) MUST BE 12.4V OR HIGHER IN
ORDER TO REPROGRAM THE PCM.
IMPORTANT
Verify whether the vehicle is K-Line Flash or CAN-Flash. Refer to the "Reprogramming System Identification" chart on the Service Tech Resources
page on the Mitsubishi Dealer Link. The procedure for PCM reprogramming on CAN-Flash vehicles is different than K-Line Flash vehicles. Be sure
10 follow the correct reprogramming instructions far the vehicle being repaired.
1.
Check the underside of the hood to verify that there is no label previously installed to indicate that this TSB reprogramming has already been done.
2.
Using the MUT-III, verify that the vehicle's ECU part number is listed in the table in Step 9. If the Software P/N is the same as or higher than the
Software PIN in the table, the PCM has already been reprogrammed for this concern. Do not continue with this bulletin procedure. Refer to Group
13 in the appropriate service manual to diagnose the DTC.
3.
Use the MUT-III to erase all DTCs set in the PCM.
