Outlander 4WD L4-2.4L (4B12) (2008)
NO <Normal condition is not displayed for item No.228.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 4 "ETACS-ECU
does not receive any signal from the front door lock actuator". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 4
NO <Normal condition is not displayed for item No.254.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 2 "ETACS-ECU
does not receive any signal from the ignition switch (IG1)". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 2
NO <Normal condition is not displayed for item No.256.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 5 "ETACS-ECU
does not receive any signal from the front door switch (LH)". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 5
NO <Normal condition is not displayed for item No.257.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 6 "ETACS-ECU
does not receive any signal from the front door switch (RH)". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 6
NO <Normal condition is not displayed for item No.258.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 7 "ETACS-ECU
does not receive any signal from the rear door switch (LH)". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 7
NO <Normal condition is not displayed for item No.259.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 8 "ETACS-ECU
does not receive any signal from the rear door switch (RH)". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 8
NO <Normal condition is not displayed for item No.260.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 9 "ETACS-ECU
does not receive any signal from the liftgate switch". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 9
NO <Normal condition is not displayed for item No.264.> : Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 3 "ETACS-ECU
does not receive any signal from the key reminder switch". See: Body and Frame/Body Control Systems/Body Control Module/Testing and
Inspection/Symptom Related Diagnostic Procedures/Inspection Procedure 3
STEP 4. Check front dome light connector D-02 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Is front dome light connector D-02 in good condition?
YES : Go to Step 5.
NO : Repair the damaged parts.
STEP 5. Front dome light bulb check
Check that the front dome light bulb is normal.
Q: Is front dome light bulb normal?
YES : Go to Step 6.
NO : Replace the front dome light bulb.
STEP 6. Check ETACS-ECU connector C-316 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Is ETACS-ECU connectors C-316 in good condition?
YES : Go to Step 7.
NO : Repair the damaged parts.
STEP 7. Check the wiring harness between front dome light connector D-02 (terminal 2/3) and ETACS-ECU connector C-316 (terminal 6/5)
Q: Are wiring harness between front dome light connector D-02 (terminal 2/3) and ETACS-ECU connector C-316 (terminal 6/5) in good condition?
YES : Go to Step 8.
NO : Repair the wiring harness.