seat Workshop Repair Guides

SEAT Workshop Service and Repair Manuals

Removing and installing operating and display unit ( Climatronic control unit J255 ) > < Cleaning evaporator
Removing and installing operating and display unit (Climatronic control unitJ255)
Removing and installing operating and display unit (Climatronic control unit -J255-)
   
–  Removing and installing operating and display unit (Climatronic control unit -J255-) → Chapter.
  E87-10055
There are different versions of the operating and display unit, Climatronic control unit -J255-, the part number index must therefore be heeded → Spare parts catalogue
t  With and without radio navigation system (or radio with large control panel)
t  With and without switch for seat heating
t  With Off button or with “Automatic air recirculation” button (vehicles with air quality sensor -G238-
  Note
t  When replacing operating and display unit, Climatronic control unit -J255-, attention must be paid to exact assignment → Spare parts catalogue.
t  After installing an operating and display unit, Climatronic control unit -J255-, perform air conditioner basic setting in the specified manner.
t  If a new operating and display unit, Climatronic control unit -J255- has been fitted and basic setting not performed, the air conditioning system compressor regulating valve -N280- is not actuated and shutoff criterion “6” appears in measured value block “2” when performing the air conditioner self-diagnosis.
t  The functions selected are indicated by lighting of LEDs in the various operating and display unit (Climatronic control unit -J255-) buttons.
t  With this version of the operating and display unit, Climatronic control unit -J255-, the dash panel temperature sensor -G56-, the temperature sensor blower -V42- and the heated rear window switch (including potentiometers for heated seats) are integrated and cannot be replaced separately.
t  Following replacement of the operating and display unit, Climatronic control unit -J255-:
t  - Always encode operating and display unit, Climatronic control unit -J255-,
t  - Always perform basic settings
t  - Always interrogate fault memory .
t  On this vehicle, the basic settings (e.g. country version, left-hand drive or right-hand drive) of the operating and display unit, Climatronic control unit -J255- are encoded by the control unit in dash panel insert -J285-. - Always data is transferred to the operating and display unit of the Climatronic control unit -J255-, via the convenience data bus system. The current valid coding is displayed in the measured value block. The direct entry of a code in the operating and display unit, Climatronic control unit -J255- is only provided for certain items of equipment (e.g. heated windscreen or sun roof with solar cells, etc.). → "Guided fault-finding" function of vehicle diagnostic, testing and information system VAS 5051 and → Engine, mechanics; Rep. Gr.01
t  The unit (°C or °F) for the temperature display of the operating and display unit, Climatronic control unit -J255- is transmitted by the control unit in dash panel insert -J285- and is determined by the code entered in this.
t  The unit used for the display can be switched by simultaneously pressing the “Air recirculation mode” and “Temperature +” buttons for the left side for more than 2 seconds.
t  The operating and display unit, Climatronic control unit -J255- then transmits the ambient temperature with the altered unit to the control unit in dash panel insert -J285-. The control unit in dash panel insert -J285- adopts this change. The same unit is used for the display in the operating and display unit, Climatronic control unit -J255- and the ambient temperature display in the dash panel insert.
t  Switching of the unit used for the display in the operating and display unit, Climatronic control unit -J255- applies to all ignition keys.
t  - Controlling of the temperature range, the minimum temperature that can be set is 16° C. → Spare parts catalogue
t  If the operating and display unit, Climatronic control unit -J255- displays a number, interrogate the fault memory of the operating and display unit, Climatronic control unit -J255- (the number “60” for example indicates a fault at the temperature sensor blower -V42-). If the display of the operating and display unit, Climatronic control unit -J255- flashes and no fault is displayed in the fault memory (e.g. with display “09”), there is a fault in the electronics of the operating and display unit, Climatronic control unit -J255-.
  E87-10052

Removing and installing operating and display unit ( Climatronic control unit J255 ) > < Cleaning evaporator