Leon Mk2
Note
|
| 1 - | Climate control with evaporator |
| q | This may only be removed when the refrigerant circuit is empty; bring the vehicle to a support workshop specialised in air conditioning work |
| q | Climate control: Removing and fitting → Chapter |
| q | Climate control: Deactivating and preparing → Chapter |
| 2 - | Servomotor for de-icing flap -V107- |
| q | With the Potentiometer on the de-icing flap servomotor -G135- |
| q | Lever colour code: blue |
| q | Removing and fitting → Chapter |
| 3 - | Air temperature sender, left foot well zone vent C1157 -G261- |
| q | Removing and fitting → Chapter |
| 4 - | Servomotor for the central flap -V70- |
| q | With the Potentiometer - servomotor centre flap -G112- |
| q | Removing and fitting → Chapter |
| 5 - | Additional heating element -Z35- with Additional air heating control unit -J604- |
| q | Only intended for vehicles with diesel engine, see → Current flow diagrams, Electrical fault finding and Fitting locations |
| q | Operation test → Vehicle diagnosis, testing and information system VAS 5051 |
| q | Removing and fitting → Chapter |
| q | From 11/06 it has been replaced by two relaysHigh temperature relay -J360- and Low temperature relay -J359-, see → Current flow diagrams, Electrical fault finding and Fitting locations |
| 6 - | Heating system heat exchanger |
| q | Removing and fitting → Chapter |
| 7 - | Servomotor for the left hand side temperature flap. -V158- |
| q | With Servomotor potentiometer for the left hand side temperature flap. -G220- |
| q | Lever colour code: white |
| q | Removing and fitting → Chapter |
| 8 - | Servomotor for air retention flap -V71- |
| q | With the Potentiometer - servomotor for air retention flap -G113- |
| q | Removing and fitting → Chapter |
| 9 - | Servomotor for air recirculation flap -V113- |
| q | With the Potentiometer on the air recirculation flap servomotor -G143- |
| q | Removing and fitting → Chapter |
| 10 - | Air temperature sender, right foot well zone vent -G262- |
| q | Removing and fitting → Chapter |
| 11 - | Air inlet opening with air recirculation / air retention (fresh air) flap |
| q | Removing and fitting → Chapter |
| 12 - | Fresh air intake temperature sensor -G89- |
| q | Removing and fitting → Chapter |
| 13 - | Fresh air turbine control unit -J126- and Fresh air turbine -V2- |
| q | Removing and fitting → Chapter |
| q | The Fresh air turbine control unit -V2- is fitted on the Fresh air turbine control unit -J126- and cannot be replaced separately |
| q | Check → Vehicle diagnosis, testing and information system VAS 5051 |
| 14 - | Dust and pollen filter |
| q | Removing and fitting → Chapter |
| q | Observe replacement intervals → Booklet |
| 15 - | Air temperature sender, evaporator outlet -G263- |
| q | Removing and fitting → Chapter |
| 16 - | Servomotor for the right hand side temperature flap -V159- |
| q | With Servomotor potentiometer for the right hand side temperature flap -G221- |
| q | Removing and fitting → Chapter |
| 17 - | Refrigerant agent tubes to the heat exchanger |
| 18 - | Grommet |
| q | To make airtight the passage for the refrigerant tubes and cooling agent in the transverse panel to the engine compartment |
| 19 - | Connection for condensation drain |
| q | Check the condensation water drainage, remove and fit the condensation drainage hose → Chapter |
| 20 - | Expansion valve |
| q | Removing and refitting the refrigerant tubes → Chapter |
| q | Removing and fitting → Chapter |
