Fabia Mk1
| Summary of Components of Hydraulic Control Unit, Brake Servo Unit/Master Brake Cylinder |
Note| t | Removing and installing the hydraulic control unit completely → Chapter. |
| t | Mount braket before assembling the brake lines. |
| t | Do not bend brake lines when assembling or when connecting. |
| t | Install brake hoses without transposition. |
| t | Brake hoses must not come into contact with other components during operating condition. |
| t | Do not remove the plugs on the connection threads and the holes in the parts carrying brake fluid until just before assembling. |
| t | Tighten all the brake line pipe screws to a tightening torque of 14 Nm. |
| t | The repair of the hydraulic control unit ABS/ASR/ESP BOSCH 8.0 is not permissible. |
| 1 - | Hydraulic control unit |
| q | ABS BOSCH 8.0 |
| q | Removing and installing LHD version → Chapter |
| q | Removing and installing RHD version → Chapter |
| q | ABS/TCS BOSCH 8.0 |
| q | Assignment → Electronic Catalogue of Original Parts |
| q | identification marking of the hydraulic unit „ABS“ |
| q | fitted as of CW 22/2004 |
| 2 - | Brake line |
| q | identification marking of the hydraulic unit „VR“ |
| q | to front right brake caliper |
| q | Connect → Chapter |
| 3 - | Brake line |
| q | identification marking of the hydraulic unit „HL“ |
| q | for rear left wheel-brake cylinder/brake caliper |
| q | Connect → Chapter |
| 4 - | Brake line |
| q | identification marking of the hydraulic unit „HR“ |
| q | for rear right wheel-brake cylinder/brake caliper |
| q | Connect → Chapter |
| 5 - | Brake line |
| q | identification marking of the hydraulic unit „VL“ |
| q | to front left brake caliper |
| q | Connect → Chapter |
| 6 - | Hydraulic control unit |
| q | ABS/TCS/ESP BOSCH 8.0 |
| q | removing and installing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| q | identification marking of the hydraulic unit „ESP“ |
| q | fitted as of CW 22/2004 |
| 7 - | Brake line |
| q | identification marking of the hydraulic unit „HZ2“ |
| q | Master brake cylinder/floating piston circuit to hydraulic control unit |
| q | Connect → Chapter |
| 8 - | Brake line |
| q | identification marking of the hydraulic unit „HZ1“ |
| q | Master brake cylinder/pressure rod piston circuit to hydraulic control unit |
| q | Connect → Chapter |
| 9 - | Support |
| q | for hydraulic control unit ABS/TCS/ESP BOSCH 8.0 |
| q | removing and installing → Chapter |
| 10 - | 8 Nm |
| q | for bracket of hydraulic control unit |
| 11 - | Line holder |
| q | for brake line |
| q | Assignment → Electronic Catalogue of Original Parts |
| 12 - | Support |
| q | for brake line |
| q | 2 units |
| q | Assignment → Electronic Catalogue of Original Parts |
| 13 - | Support |
| q | for brake line |
| q | 3 units |
| q | Assignment → Electronic Catalogue of Original Parts |
| 14 - | Brake servo unit |
| q | check → Chapter |
| q | Removing and installing LHD version → Chapter |
| q | Removing and installing RHD version → Chapter |
| 15 - | Master brake cylinder |
| q | cannot be repaired, replace completely in the event of faults |
| q | Check tightness → Chapter |
| q | removing and installing → Chapter |
| 16 - | Brake fluid reservoir |
| 17 - | Self-locking nuts, 20 Nm |
| q | replace after each removal |
| q | for bracket to body |
| 18 - | Support |
| q | for ABS, ABS/TCS, ABS/TCS/ESP BOSCH 8.0 |
| q | removing and installing → Chapter |
| 19 - | Hexagon collar nut, 20 Nm |
| q | replace after each removal |
| q | for bracket to body |
| 20 - | Support |
| q | for hydraulic control unit ABS, ABS/TCS BOSCH 8.0 |
| q | removing and installing → Chapter |
| 21 - | Support |
| q | for brake line |
| q | 2 units |
| q | Assignment → Electronic Catalogue of Original Parts |
