Fabia Mk1 Automatic Gearbox: Disassembling and Assembling Gearshift Mechanism
| Disassembling and assembling the gearshift mechanism |
Note| Grease bearing and friction surfaces with polycarbamide grease -G 052 142 A2- SP No. |
| 1 - | Grip for selector lever |
| q | removing and installing → Chapter |
| 2 - | Bushing |
| q | interlocks in the selector lever grip |
| q | blocks pulling off of the selector lever grip |
| 3 - | Cover |
| q | with selection range |
| 4 - | Cover strip |
| q | insert in surround → Item |
| 5 - | Selector lever position indicator |
| q | Clip printed circuit board for selector lever position and indicator (lighting) off or on |
| q | The contacts for selector lever position point towards the contact spring → Item of the selector lever |
| q | Secure plug housing with holder → Item to surround → Item |
| q | Hook fiberoptic cable and cable to plug housing onto its supports on the surround. |
| q | Disconnect and connect plug connection → Chapter |
| 6 - | Bracket |
| q | for wiring loom |
| 7 - | Surround |
| q | to remove pull off upwards with selector lever position indicator → Item and cover → Item |
| 8 - | 7 Nm |
| 9 - | Washer |
| 10 - | Locking segment |
| 11 - | Bracket |
| 12 - | Latch spring with roller |
| q | catches in the slots of the selector lever → Item |
| q | adjust → Chapter |
| 13 - | Selector lever |
| q | with tension rod, pressure spring, slots, contact spring for selector lever position and release for interlock cable |
| q | removing and installing → Chapter |
| 14 - | Roller |
| 15 - | Circlip |
| 16 - | Gasket |
| q | with studs press into the supports of the gearshift bracket → Item |
| 17 - | Gearshift bracket |
| q | need not be removed to replace the selector lever control cable or the component parts of the gearshift mechanism |
| 18 - | Collar screw |
| q | with serration |
| q | only counterhold screw head, do not turn! |
| q | grease at shank |
| 19 - | Locking lever |
| q | to lock in selector lever position “P” |
| 20 - | Washer |
| 21 - | 2,5 Nm |
| 22 - | Gasket |
| q | always replace |
| 23 - | 8 Nm |
| q | 2 pieces |
| 24 - | Bottom cover |
| q | for gearshift bracket |
| 25 - | 1,5 Nm |
| q | 14 pieces |
| 26 - | Gasket |
| q | always replace |
| 27 - | Contact spring |
| 28 - | Contact plate |
| 29 - | 4 Nm |
| q | to release and tighten put selector lever in “P” |
| 30 - | 1,3 Nm |
| q | 2 pieces |
| q | Solenoid on gearshift bracket |
| 31 - | Selector lever lock solenoid -N110- |
| q | removing and installing → Chapter |
| q | remove and install in selector lever position “1” only |
| q | Move wiring loom in such a way that it can neither be damaged by the selector lever nor by the selector lever lock solenoid |
| q | when removing pay attention to the spring and locking bolt |
| q | install together with the locking bolt and spring, while doing so move the selector lever up and down a little |
| q | can be checked in the electrical test and in the measured value block → The Engine; Rep. Gr.01 |
| 32 - | Pressure spring |
| 33 - | Locking bolt |
| 34 - | 13 Nm |
| q | always replace |
| 35 - | Washer |
| 36 - | 25 Nm |
| q | with collar |
| q | 4 pieces |
| 37 - | Gasket |
| q | always replace |
| 38 - | Retaining clip |
| q | always replace |
| q | for selector lever control cable on gearshift bracket |
| q | install the angled end towards the inside of the gearshift bracket |
| 39 - | Selector lever control cable |
| q | do not bend or buckle |
| q | if the boot is damaged the selector lever control cable must be replaced |
| q | testing and adjusting → Chapter |
| q | removing and installing → Chapter |
| q | do not grease the ball sockets at the cable extremities |
| 40 - | 8 Nm |
| q | for selector lever control cable |
| 41 - | Retaining clip |
| q | for selector lever control cable on gearbox |
| q | always replace |
| q | angled end point towards the end of the selector lever control cable |
| 42 - | 25 Nm |
| q | 2 pieces |
| q | for support to gearbox |
