Fabia Mk2
| V - Summary of components of drive shaft with CV joint |
Note| t | Assignment of the drive shafts → Electronic Catalogue of Original Parts. |
| t | Grease joint if necessary, when replacing the joint boot. |
| t | Spread the grease mass evenly in the joint. |
| 1 - | Right joint boot (tubular shaft) |
| q | Assignment → Electronic Catalogue of Original Parts |
| 2 - | Screw |
| q | replace after each removal |
| q | first of all pre-tighten all screws crosswise up to 10 Nm and subsequently tighten crosswise to final torque: |
| Screw M 8 x 48 = 20 Nm + 180° |
| Screw M 10 x 52 = 50 Nm + 45° |
| q | Assignment → Electronic Catalogue of Original Parts |
| 3 - | Base |
| q | Assignment → Electronic Catalogue of Original Parts |
| 4 - | Open warm-type clamp |
| q | replace |
| q | tensioning → Anchor |
| 5 - | Joint boot for inner CV joint |
| q | inspect for tears and chafing points |
| q | remove from CV joint with drift |
| q | before installation coat the inside of the cap with sealant -D 454 300 A2- |
| q | Assignment → Electronic Catalogue of Original Parts |
| 6 - | Disc spring |
| q | Fitting position → Anchor |
| 7 - | Inner CV joint |
| q | must be replaced completely |
| q | pressing off → Anchor |
| q | pressing on → Anchor |
| q | grease → Anchor |
| q | check → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 8 - | Gasket |
| q | The adherend must be free of grease and oil |
| q | replace after each removal |
| q | Pull off protective foil and stick in joint |
| q | Assignment → Electronic Catalogue of Original Parts |
| 9 - | Circlip |
| q | replace |
| q | remove and install with circlip pliers, e.g. -VW 161 A- |
| q | Assignment → Electronic Catalogue of Original Parts |
| 10 - | Left drive shaft (solid shaft) |
| q | Assignment → Electronic Catalogue of Original Parts |
| 11 - | Open warm-type clamp |
| q | replace |
| q | tensioning → Anchor |
| 12 - | Collar |
| q | inspect for tears and chafing points |
| q | Assignment → Electronic Catalogue of Original Parts |
| 13 - | Open warm-type clamp |
| q | replace |
| q | tension with tensioning pliers, e. g. -V.A.G 1682- → Anchor |
| 14 - | Disc spring |
| q | Fitting position → Anchor |
| 15 - | Thrust ring |
| q | Fitting position → Anchor |
| 16 - | Circlip |
| q | replace |
| q | insert in the shaft groove |
| 17 - | Outer CV joint |
| q | must be replaced completely |
| q | Removing outer CV joint → Anchor |
| q | before installing grease the serration with polycarbamide grease -G 052 142 A2- |
| q | installation: carefully drive onto the shaft with a plastic hammer until the compressed circlip expands |
| q | grease → Anchor |
| q | check → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 18 - | Thrower ring |
| 19 - | Twelve-point nut |
| q | 50 Nm + 45° |
| q | Removing and installing nut for securing the drive shaft → Chapter |
| q | replace after each removal |
Note
|
| Ø Joint (mm) | Total grease quantity (g) | Grease quantity distribution | |
| Outer joint (g) | Inner joint and joint boot (g) | ||
| Outer joint Ø 90 | 80 +10 | 80 +10 | --- |
| Inner joint Ø 90 | 80 +10 | 40 +5 | 40 +5 |
