Fabia Mk2
| IV - Summary of components of the wheel bearing, suspension strut, drive shaft, brake FS-IIl |
Note| t | Welding and straightening work is not allowed on the bearing and wheel control components of the front wheel suspension. |
| t | Always replace the self-locking nuts and screws. |
| t | Always replace corroded self-locking nuts and screws. |
| 1 - | Suspension strut |
| q | removing and installing → Chapter |
| q | repairing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 2 - | Drive shaft with CV joint |
| q | removing and installing → Chapter |
| q | check → Chapter |
| q | repairing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 3 - | Base |
| q | Assignment → Electronic Catalogue of Original Parts |
| 4 - | Fillister head screw with internal serrations |
| q | replace after each removal |
| q | first pre-tighten all screws crosswise up to 10 Nm and subsequently tighten crosswise to final tightening torque: |
| Screw M 8 x 48 = 20 Nm + 180° |
| Screw M 10 x 52 = 50 Nm + 45° |
| q | Assignment → Electronic Catalogue of Original Parts |
| 5 - | Drive shaft with tripod joint |
| q | removing and installing → Chapter |
| q | repairing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 6 - | Fillister head screw with internal serrations |
| q | replace after each removal |
| q | first pre-tighten all screws crosswise up to 10 Nm and subsequently tighten crosswise to final tightening torque: |
| Screw M 10 x 23 = 50 Nm + 45° |
| q | Assignment → Electronic Catalogue of Original Parts |
| 7 - | Brake disc, internally ventilated |
| 8 - | Wheel bolt |
| q | Assignment → Electronic Catalogue of Original Parts |
| q | Tightening torque → Chapter |
| 9 - | Twelve-point nut 50 Nm + 45° |
| q | replace after each removal |
| q | Do not grease thread of the outer joint of the drive shaft. |
| q | Assignment → Electronic Catalogue of Original Parts |
| 10 - | Screw, 4 Nm |
| 11 - | Brake pad |
| q | removing and installing → Chapter |
| 12 - | Brake caliper |
| q | Assignment → Electronic Catalogue of Original Parts |
| q | do not release brake hose when working on the front wheel suspension |
| q | tie up with wire or anything similar |
| q | repairing → Chapter |
| 13 - | Guide bolt, 28 Nm |
| 14 - | Cap |
| q | removing |
| 15 - | Screw, 10 Nm |
| 16 - | Wheel hub with wheel bearing |
| q | for vehicles with ABS the sensor ring is built into the wheel hub |
| q | The wheel hub and the wheel bearing are a single unit; it does not need servicing and is free of play; it is not possible to undertake any kind of adjustment or repair work on it. |
| q | The sensor ring for ABS cannot be replaced individually |
| q | replace after each removal, wheel hub with wheel bearing is destroyed during removal |
| q | Removing and installing wheel hub with wheel bearing up to CW 11 2008 → Chapter |
| q | Removing and installing wheel hub with wheel bearing as of CW 12 2008 → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 17 - | Cover plate |
| 18 - | Nut, 20 Nm + 90° |
| q | replace after each removal |
| 19 - | Track rod and track-rod ends |
| q | removing and installing → Chapter |
| 20 - | Wheel-bearing housing |
| q | removing and installing up to CW 11 2008 → Chapter |
| q | removing and installing as of CW 12 2008 → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 21 - | Nut, 60 Nm + 90° |
| q | replace after each removal |
| 22 - | Screw |
| q | replace after each removal |
| q | the tip of bolt must point in the direction of travel |
| 23 - | ABS wheel speed sensor |
| q | Assignment → Electronic Catalogue of Original Parts |
| 24 - | Allan screw, 8 Nm |
| q | for speed sensor ABS |
| 25 - | Nut, 40 Nm |
| q | Assignment → Electronic Catalogue of Original Parts |
| 26 - | Coupling rod |
| q | Assignment → Electronic Catalogue of Original Parts |
