Octavia Mk1
|
1 - | Brake servo unit |
t | with master brake cylinder and brake fluid reservoir |
t | Remove and install brake servo unit → Chapter |
2 - | Brake pressure sender -1--G201-1) |
t | removing and installing → Chapter |
3 - | Sensor unit for ESP -G419- |
t | RHD 4x4 vehicles without -G251- |
t | Fitting location: next to the steering column under the dash panel |
4 - | Steering angle sender -G85-1) |
t | Fitting location: on the steering column between the steering wheel and the steering column switch |
5 - | ABS warning light -K47- |
t | Fitting location: in the dash panel insert |
t | function → Chapter |
6 - | Hand brake/brake fluid level warning light -K14/33- |
t | Fitting location: in the dash panel insert |
t | function → Chapter |
7 - | ESP warning light -K155- |
t | Fitting location: in the dash panel insert |
t | function → Chapter |
8 - | Parts of ABS system on rear axle |
t | Rear right and rear left wheel speed sensors -G44/G46-1) |
– | removing and installing → Chapter |
– | Installing wheel speed sensor cables → Chapter |
t | Pulse rotor for the wheel speed sensor at the rear on the right and left |
– | check → Chapter |
– | removing and installing: The pulse rotor must be changed together with the wheel hub → Axles, steering; Rep. gr.42 |
9 - | Brake vacuum pump -V192-1) |
t | only on vehicles with automatic gearbox in combination with the limit values of exhaust gas according to EU-4 |
t | Fitting location: on the left of the assembly carrier |
t | is checked by self-diagnosis in the engine control unit → Engine, Fuel Injection and Ignition System; Rep. gr.01 |
t | removing and installing → Chapter |
10 - | Diagnostic connection |
t | Fitting location: in the storage compartment on the driver's side |
11 - | Brake light switch -F-1) |
t | is open in off position |
– | adjust → Chapter |
– | remove by turning 90° to the left → Chapter |
– | install by turning 90° to the right → Chapter |
t | check: measured value block 003 → Chapter |
12 - | Control unit for ABS/EDL/ESP -J104- |
t | Fitting location: at the hydraulic unit in left of engine compartment |
t | is checked by self-diagnosis |
t | Check the multi-pin plug connection to the control unit → Chapter |
t | switch off the ignition before disconnecting the plug connection |
13 - | Hydraulic unit for ABS/EDL/ESP -N55-1) |
t | Fitting position: left of engine compartment |
t | the hydraulic unit -N55- consists of the hydraulic pump -V64- and the valve block with the inlet and exhaust valves |
t | when changing, absolutely close the old part with a plug from the mounting part kit; SP no. → Electronic Catalogue of Original Parts |
t | Remove and install hydraulic control unit (hydraulic unit -N55- with control unit -J104- → Chapter |
t | Do not separate the hydraulic pump -V64- from the valve block. |
t | Repairing the hydraulic control unit → Chapter |
14 - | Parts of ABS system on front axle |
t | Front right and front left wheel speed sensors -G45/G47-1) |
– | removing and installing → Chapter |
– | Installing wheel speed sensor cables → Chapter |
t | Pulse rotor for the wheel speed sensor at the front on the right and left |
– | check → Chapter |
– | removing and installing: The pulse rotor must be changed together with the wheel hub → Axles, steering; Rep. gr.40 |
15 - | Longitudinal acceleration sender -G251-1) |
t | Fitting location: |
– | only RHD 4x4 vehicles ⇒ on the central pipe to the right, near right pillar -A- |