RAV4 2WD L4-2.5L (2AR-FE) (2009)
INSTALLATION
HINT:
-
Use the same procedures for the RH side and LH side.
-
The procedures listed below are for the LH side.
CAUTION: Be sure to read the precautionary notices concerning the SRS airbag system before servicing it See: Restraint
Systems/Air Bag Systems/Service Precautions.
1. INSTALL AIRBAG SENSOR REAR LH
(a) Install the airbag sensor with the bolt.
Torque: 9.0 Nm (92 kgf-cm, 80 in-lbf)
NOTICE:
-
If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new
one.
-
When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other
parts.
2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/ Rear No. 2 Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service
and Repair/Installation
3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Rear No. 2 Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service
and Repair/Installation
4. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)
5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH See: Restraint Systems/Seat Belt Systems/Seat Belt/Service and Repair/Rear
Seat Outer Belt Assembly/Installation
6. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/o Rear No. 2 Seat)
7. INSTALL REAR FLOOR FINISH PLATE See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
8. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
9. INSTALL REAR FLOOR NO. 3 BOARD
10. INSTALL REAR FLOOR NO. 2 BOARD
11. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) See: Body and Frame/Seats/Service and Repair/Rear No. 2 Seat
Assembly/Installation
12. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
13. INSTALL NO. 2 SEAT LEG COVER LH (w/ Rear No. 2 Seat) See: Body and Frame/Seats/Service and Repair/Rear No. 2 Seat
Assembly/Installation
14. INSTALL NO. 2 SEAT LEG COVER RH (w/ Rear No. 2 Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
15. INSTALL NO. 2 SEAT HINGE COVER LH (w/ Rear No. 2 Seat) See: Body and Frame/Seats/Service and Repair/Rear No. 2 Seat
Assembly/Installation
16. INSTALL NO. 2 SEAT HINGE COVER RH (w/ Rear No. 2 Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
17. INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
18. INSTALL REAR FLOOR NO. 1 BOARD (w/o Rear No. 2 Seat)
19. INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)
20. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/o Rear No. 2 Seat)
21. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
22. INSTALL REAR DOOR SCUFF PLATE LH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
24. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light See: Restraint Systems/Air Bag Systems/Testing and Inspection/Symptom Related Diagnostic
Procedures/Problem Symptoms Table.