|
Nm
|
Starter to transmission
|
40
|
Starter to cylinder block
|
25
|
Drive disc to crankshaft
|
60
|
Exhaust manifold to cylinder head
|
22 1)
|
Battery support to body
|
15
|
Camshaft sensor fastening bolt to camshaft housing
|
16
|
DIS Ignition Module to camshaft housing carrier
|
8
|
Throttle valve injection housing to intake manifold
|
22
|
Upper part of throttle valve injection housing to throttle valve
injection housing
|
6
|
Throttle body to intake manifold
|
9
|
Pressure plate to camshaft housing
|
8
|
Dynamic oil level control to oil pan
|
8
2)
|
Intake manifold to cylinder head
|
22 1)
|
Accelerator pedal to bulkhead
|
12
|
Engine vent flange to cylinder block
|
8
|
Alternator to alternator support
|
35
|
Alternator to alternator shackle
|
20
|
Transmission to cylinder block
|
60
|
Alternator support to cylinder block
|
35
|
Left engine damping block support to transmission
|
35
|
Engine damping block support to cylinder block
|
50
|
Bowden cable bracket to intake manifold
|
9
|
Crankshaft pulse pickup bracket to oil pump
|
10
|
Wiring harness bracket to intake manifold
|
20
|
Rear engine damping block bracket to transmission
|
80
|
Engine damping block bracket to engine damping block support
(left)
|
55
|
Engine damping block bracket to engine damping block support
(right)
|
55
|
Engine damping block bracket to engine damping block (left)
|
55
|
Engine damping block bracket to engine damping block (right)
|
55
|
Rear toothed belt cover to camshaft housing
|
6
|
Rear toothed belt cover to oil pump housing
|
6
|
Heat shield to exhaust manifold
|
8
|
Heat shield sleeves (spark plugs) to cylinder head
|
25
|
Crankshaft pulse pickup to bracket
|
8
|
Increment disc to toothed belt drive gear
|
95 + 30° + 15° 3)
|
Wiring trough to cylinder head
|
8
|
V-belt tensioner to alternator support
|
25
|
Refrigerant line to receiver-dryer
|
20
|
Refrigerant line to refrigerant line intake side (air cleaner
housing)
|
20
|
Knock sensor to cylinder block
|
20
|
Fuel distributor tube to intake manifold
|
4
|
Fuel supply and return line to throttle valve guards
|
15
|
Coolant pump to cylinder block
|
8
|
Coolant pipe to transmission
|
60
|
Coolant pipe to cylinder block
|
20
|
Crankshaft bearing cap to cylinder block
|
50 + 45° + 15° 3)
|
Oxygen sensor to exhaust manifold
|
40
|
Oxygen sensor for catalytic converter control
|
40
|
Alternator shackle to intake manifold
|
20
|
Fan housing to radiator
|
5
|
Rear engine damping block to bracket
|
55
|
Rear engine damping block to front axle body
|
55
|
Left engine damping block to body (side member)
|
20
|
Right engine damping block to body (side member)
|
35
|
Front engine damping block to transmission
|
60
|
Front engine damping block to front axle body
|
55
|
Camshaft housing cover to camshaft housing
|
8
|
Camshaft pulley to camshaft
|
45
|
Oil drain bolt to oil pan (sheet steel with hex screw and copper
washer)
|
55
|
Oil drain bolt to oil pan (aluminium with hex screw and copper
washer)
|
45
|
Oil drain bolt to oil pan (aluminium with inner torx with O-ring
insert)
|
14
|
Oil pressure switch to oil pump
|
30
|
Oil filter to oil pump
|
15
|
Oil lines to radiator (AT)
|
25
|
Oil pump to cylinder block
|
10
|
Oil pump cover to oil pump
|
6
|
Oil intake pipe to oil pump
|
8
2)
|
Oil intake pipe to cylinder block
|
8
|
Oil baffle plate to oil pan
|
8
|
Oil pan to transmission
|
40
|
oil pan to oil pump
|
10
2)
|
Oil pan to cylinder block
|
10 1)
|
Swing arm to spring strut
|
65 1)
|
Con-rod bearing cap to con-rod
|
25 + 30° 3)
|
Wheel to wheel hub
|
110
|
Hose clamps for air intake hose
|
3.5
|
Flywheel to crankshaft
|
35 + 30° + 15° 3)
|
Coolant temperature sensor to intake manifold
|
20
|
Support to alternator and intake manifold
|
20
|
Thermostat housing to cylinder head
|
10
|
Carrier plate (DIS ignition module) to camshaft housing
|
12
|
Lower radiator bracket to front axle body
|
15
|
Condenser to radiator
|
5
|
Closure bolt, safety valve to oil pump
|
50
|
Front axle body to body (all bolts)
|
90 + 45° + 15° 3)
|
Front exhaust pipe to exhaust manifold (hex bolts)
|
35 4)
|
Front exhaust pipe to exhaust manifold (hex nuts)
|
45 1)
|
Toothed belt cover – upper part to rear toothed belt
cover
|
4
|
Toothed belt cover, lower part to rear toothed belt cover
|
4
|
Toothed belt tension roller to oil pump housing
|
20
|
Spark plug to cylinder head
|
25
|
Intermediate spindle to steering intermediate spindle
|
22 5)
|
Cylinder head and camshaft housing to cylinder block
|
25 + 85° + 85° + 20° 3)
|