|
Special Service Tools
|
KM-113-2
|
Bracket
|
|
Transmission holder mount with KM-552, KM-444-C
(F13/F13+/F17/F17+/F18/F23/F35)
|
|
|
|
KM-160-A
|
Differential housing holding wrench 1)
|
|
Differential preassembly (F18)
|
|
|
|
KM-161-B
|
Bearing Puller
|
|
Remove various transmission parts (F13/F13+/F17/F18/F35)
|
|
|
|
KM-248
|
Remover
|
|
To remove various bearings out of clutch housing with KM-248-2
and KM-248-4 (F23)
|
|
|
|
KM-258
|
Installation sleeve 2)
|
|
To press on various transmission parts (F13/F13+/F17/F18)
|
|
|
|
KM-277
|
Bevel gear bearing installer sleeve 1)
|
|
To press on various transmission parts (F13/F13+/F17/F18)
|
|
|
|
KM-303
|
Removal Sleeve
|
|
Place sleeve underneath when driving tapered roller bearing
outer race from bearing ring (F13/F13+/F17)
|
|
|
|
KM-304
|
Remover
|
|
To drive tapered roller bearing outer race from transmission
with KM-451. Place KM-502-A underneath (F13/F13+/F17/F18)
|
|
|
|
KM-305
|
Remover / Installer
|
|
To press various bearing parts out of housing
|
|
|
|
KM-307-B
|
Remover Plate
|
|
Press off various transmission parts (F13/F13+/F17/F17+/F18)
|
|
|
|
KM-308
|
Remover / Installer
|
|
Driving pins in/out for shift rod and shift fork
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-311
|
Installer Sleeves
|
|
To press on various transmission parts (F13/F13+/F17/F18)
|
|
|
|
KM-313
|
Sliding Hammer
|
|
Bearing of main shaft from transmission housing (F18)
|
|
|
|
KM-328-B
|
Remover
|
|
Pulling locking plugs out of end shield
(F13/F13+/F17/F17+/F18/F35)
|
|
|
|
KM-334
|
Assembly Sleeves
|
|
To press spacer washer onto main shaft (F13/F13+/F17)
|
|
|
|
KM-396
|
Ring pliers
|
|
Removing and installing various retaining rings
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-403
|
Thrust piece
|
|
Counterhold for pressing both bearing rings for differential
|
|
|
|
KM-407-A
|
Ring Installer
|
|
Press ball bearing from gear cluster (F18)
|
|
|
|
KM-443-B
|
Ring pliers
|
|
To remove retaining rings for fastening main shaft and drive
shaft to end shield (F13/F13+/F17/F18)
|
|
|
|
KM-444-C
|
Transmission Holder
|
|
To hold transmission housing in conjunction with KM-113-2
(F13/F13+/F17/F18)
|
|
|
|
KM-446
|
Installer Drift
|
|
To install axle shaft seal rings (F13/F13+/F17)
|
|
|
|
KM-447
|
Remover / Installer
|
|
To screw/unscrew bearing ring in/from transmission
(F13/F13+/F17)
|
|
|
|
KM-451
|
Remover / Installer
|
|
Pressing in and out of tapered roller bearing outer race
(F13/F13+/F17/F18)
|
|
|
|
KM-453
|
Pusher
|
|
Press tapered roller bearing inner race onto differential
housing (F13/F13+/F17)
|
|
|
|
KM-454-B
|
Remover / Installer
|
|
Bearings for Main and Drive Shaft in Transmission housing and
Seal Rings in Bearing Ring and Transmission housing, Remove and
Install (F13/F13+/F17)
|
|
|
|
KM-456
|
Centring drift
|
|
Pre-installation of Differential (F13/F13+/F17)
|
|
|
|
KM-458-A
|
Mounting Drift
|
|
To clamp differential in vice (F13/F13+/F17)
|
|
|
|
KM-466-A
|
Remover / Installer
|
|
Various pressing operations (F13/F13+/F17/F18)
|
|
|
|
KM-473
|
Sleeve
|
| |
Pressing on 5th gear (driving/driven) (F17+)
|
|
|
|
KM-483
|
Adapter
|
|
To drive outer sleeve for main shaft out of transmission
housing, with KM-313 (F18)
|
|
|
|
KM-500-A
|
Remover / Installer
|
|
Removing bearing from differential with KM-500-5 in conjunction
with KM-6118 (F17+/F23)
|
|
|
|
KM-502-A
|
Spacer
|
|
Tapered Roller Bearing Outer Race, Remove and Install (F18)
|
|
|
|
KM-514
|
Installer Sleeve
|
|
Press various transmission parts on and in
(F13/F13+/F17/F18/F23/F35)
|
|
|
|
KM-519.
|
Installer Drift
|
|
To install axle shaft seal rings (F18/F23/F35)
|
|
|
|
KM-520
|
Remover / Installer
|
|
Removing and installing bearing ring in transmission housing
(F18)
|
|
|
|
KM-522
|
Pusher
|
|
Tapered roller bearing inner rings on differential housing
(F13/F13+/F17/F18/F23)
|
|
|
|
KM-523
|
Remover / Installer
|
|
Driving in needle bearing for drive shaft (F17+/F18)
|
|
|
|
KM-524-A
|
Mounting Drift
|
|
Differential housing in vice (F18)
|
|
|
|
KM-527-A
|
Adjuster
|
|
Adjust Transmission Shift Linkage (F13/F13+/F17/F18/F35)
|
|
|
|
MKM-536-A
|
Friction Coefficient Meter
|
|
To measure breakaway torque in conjunction with KM-6037 or
KM-995-A (F13/F13+/F17/F18)
|
|
|
|
KM-552
|
Installer
|
|
Holding end shield during installation work
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-553-A
|
Remover
|
|
Removing 5th gear (driving) from drive shaft
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-554
|
Installer
|
|
Press on 5th gear (F13/F13+/F17/F18)
|
|
|
|
KM-556-A
|
Puller Set
|
|
Pulling out bearing for main and drive shaft in transmission
housing (F13/F13+/F17/F17+)
|
|
|
|
KM-557-A
|
Puller Set
|
|
To remove axle shaft seal rings from the transmission housing
(F13/F13+/F17/F18/F23/F35)
|
|
|
|
KM-559-A
|
Puller
|
|
Releasing 5th gear synchro body with shift sleeve and gear wheel
for 5th gear. Releasing transmission housing (F17+/F35).
|
|
|
|
KM-569-A
|
Plug Remover
|
|
To lever out female pin on the shift guide
(F13/F13+/F17/F18/F35)
|
|
|
|
KM-577
|
Installer
|
|
Press synchro body 3rd/4th gear onto main shaft
(F13/F13+/F17/F18/F35)
|
|
|
|
MKM-599
|
Inner Extractor
|
|
Pulling out bearing for main shaft from transmission housing
(F13/F13+/F17/F17+)
|
|
|
|
KM-619
|
Remover / Installer
|
|
Drive in seal ring for shifter rod
|
|
|
|
KM-621-A
|
Installer
|
|
To measure pressure collar and pretension of differential
tapered roller bearing with KM-621-23 (F23)
|
|
|
|
KM-622-A
|
Transmission Holder
|
|
Transmission mount
|
|
|
|
KM-652
|
Flywheel Holder
|
|
To lock flywheel when removing and installing clutch
(F13/F13+/F17/F18/F23)
|
|
|
|
KM-672
|
Remover
|
|
Outer Race of Tapered Roller Bearing on Differential in Clutch
Housing, Remove(F35)
|
|
|
|
KM-708
|
Assembly Sleeve
|
|
Outer Race of Tapered Roller Bearing on Drive Shaft from Clutch
Housing, Press (F35)
|
|
|
|
KM-727
|
Remover
|
|
Knocking locking plugs with out of end shield with KM-328-B
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-734
|
Guide Bolt
|
|
To centre clutch (F13/F13+/F17)
|
|
|
|
KM-735
|
Guide Bolt
|
|
To centre clutch (F18)
|
|
|
|
KM-736
|
Guide Bolt
|
|
To centre clutch (F23)
|
|
|
|
KM-743
|
Installer
|
|
Outer race for main shaft roller bearing in transmission housing
in conjunction with KM-J-8092 (F18)
|
|
|
|
KM-781
|
Installer
|
|
Counterhold for pressing the differential axle off and on using
KM-872 (F35)
|
|
|
|
KM-856
|
Tool Kit
|
|
Overhaul manual transmission (contains KM-857 to KM-873, KM-875
to KM-880)
|
|
|
|
KM-857
|
Thrust piece
|
|
Protection of shaft bearing journal on the transmission and/or
main shaft (F35)
|
|
|
|
KM-858
|
Lifting eye
|
|
Separate the transmission housing from the clutch housing using
KM-857 and KM-559-1-A (F35)
|
|
|
|
KM-859
|
Puller
|
|
Detach the drive shaft from the clutch housing using KM-857
(F35)
|
|
|
|
KM-860
|
Assembly clamping device
|
|
Hold synchro unit for 1st/2nd gear together (F35)
|
|
|
|
KM-861
|
Remover
|
|
Push main shaft out of clutch housing using KM-328-B (F35)
|
|
|
|
KM-862
|
Puller
|
|
Remove bearing ring from main shaft using KM-863 (F35)
|
|
|
|
KM-863
|
Clamping device
|
|
Press inner race of tapered roller bearing off main or drive
shaft using KM-862 or KM-867 (F35)
|
|
|
|
KM-864
|
Remover / Installer
|
|
Pressing in and out of various tapered roller bearings (F35)
|
|
|
|
KM-865
|
Remover
|
|
Drive shaft bearing rings (F35)
|
|
|
|
KM-866
|
Crossed helical press
|
|
Press on drive shaft bearing rings (F35)
|
|
|
|
KM-867
|
Pull ring
|
|
Pull off drive shaft bearing rings using KM-863 (F35)
|
|
|
|
KM-868
|
Installer
|
|
Press on outer race of tapered roller bearing for drive shaft
using KM-869 and KM-514 (F35)
|
|
|
|
KM-869
|
Counterhold
|
|
Press on outer race of tapered roller bearing for drive shaft
using KM-514 (F35)
|
|
|
|
KM-870
|
Adapter
|
|
Pull gasket for shifter rod out of clutch housing using KM-881
and KM-J-7004 (F35)
|
|
|
|
KM-871
|
Installer/removal drift
|
|
To drive pins in/out for shifter rod support bracket (F35)
|
|
|
|
KM-872
|
Installer/removal drift
|
|
Insert and remove bushings for shifter rod and gearshift lever
shaft bushing, press off/onto differential axle using KM-781
(F35)
|
|
|
|
KM-873
|
Installer
|
|
Press on inner race of tapered roller bearing for differential
using KM-403 (F35)
|
|
|
|
KM-875
|
Bracket
|
|
Holding the dial gauge MKM-882 (F35)
|
|
|
|
KM-876
|
Shift driver
|
|
Turning the main shaft with speed-adjustable hand drill
(F35)
|
|
|
|
KM-877
|
Millimetre washer
|
|
Adjust axial play of main shaft in transmission housing
(F35)
|
|
|
|
KM-878
|
Adjuster
|
|
Adjust axial play for differential gear using KM-876 and KM-879
(F35)
|
|
|
|
KM-879
|
Weight (10 kg)
|
|
Adjust axial play for differential gear using KM-878 (F35)
|
|
|
|
KM-880
|
Shift driver
|
|
Rotating of drive shaft with speed-adjustable hand drill
(F35)
|
|
|
|
MKM-881
|
Puller
|
|
Pull gasket for shifter rod out of clutch housing using KM-870
and KM-J-7004 (F35)
|
|
|
|
MKM-882
|
Dial gauge
|
|
To measure axial clearance of main or drive shaft using
KM-875
|
|
|
|
MKM-883-1
|
Engine Bridge
|
|
Holding/lowering/raising the engine
(F13/F13+/F17/F18/F23/F35)
|
|
|
|
MKM-883-2
|
Retainer plate
|
|
To hold engine in conjunction with MKM-883-1 and MKM-883-3 when
removing transmission
|
|
|
|
MKM-883-3
|
Accessories for MKM-883-1
|
|
To remove transmission in conjunction with MKM-883-2
|
|
|
|
KM-914
|
Remover / Installer
|
|
Fluid Filler Bolt, Remove and Install
|
|
|
|
KM-982
|
Mount
|
|
Gearshift cover mount for overhauling operations on manual
transmission (F13/F13+/F17/F18)
|
|
|
|
KM-983
|
Remover
|
|
To remove intermediate selector press sleeve and gate pin with
KM-328-B (F13/F13+/F17/F18)
|
|
|
|
KM-995-A
|
Adapter
|
|
To turn differential completely to check bearing pretension with
MKM-536-A (F18)
|
|
|
|
KM-6001-A
|
Engine Mount
|
|
Centring the engine when removing the transmission
(F13/F13+/F17/F18/F23/F35)
|
|
|
|
KM-6037
|
Adapter
|
|
To turn differential completely to check bearing pretension in
conjunction with MKM-536-A (F13/F13+/F17)
|
|
|
|
KM-6042
|
Dismantling Key
|
|
To remove shift cables from shift guide assembly (F23)
|
|
|
|
KM-6059
|
Assembly Sleeve
|
|
Assembly of central release (F23)
|
|
|
|
KM-6065
|
Remover
|
|
To remove clamping piece for shift Bowden cables (F23)
|
|
|
|
KM-6101
|
Remover
|
|
To remove intermediate shaft cover in conjunction with KM-328-8
(F23)
|
|
|
|
KM-6102
|
Installer
|
|
To install intermediate shaft cover in conjunction with KM-523-1
(F23)
|
|
|
|
KM-6110
|
Remover
|
|
To remove main shaft bearing out of clutch housing (F23)
|
|
|
|
KM-6111
|
Installer
|
|
To install main shaft bearing in clutch housing in conjunction
with KM-523-1 (F23)
|
|
|
|
KM-6112
|
Installer
|
|
Spacer sleeve for drive shaft in clutch housing in conjunction
with KM-523-1 (F23)
|
|
|
|
KM-6113
|
Remover
|
|
Differential bearing outer race in transmission housing and
clutch housing (F23)
|
|
|
|
KM-6114
|
Installer
|
|
Installing differential bearing outer race in transmission and
clutch housings in conjunction with KM-523-1 (F23)
|
|
|
|
KM-6115
|
Bracket for Clutch Housing
|
|
Transmission mount in conjunction with KM-113-2
(F17+/F23/F35)
|
|
|
|
KM-6116
|
Remover / Installer
|
|
To remove and install transmission shafts out of / in
transmission housing bearing and to separate main housing and
clutch housing (F23)
|
|
|
|
KM-6117
|
Transmission Shaft Holder
|
|
To lock drive shaft to release shaft unions (F23)
|
|
|
|
KM-6118
|
Remover
|
|
Removing differential bearings in conjunction with workshop
press and KM-500-5 (F23)
|
|
|
|
KM-6119
|
Installer
|
|
To press intermediate shaft bearing into clutch housing in
conjunction with KM-523-1 (F23)
|
|
|
|
KM-6120
|
Installer
|
|
To drive in drive shaft bearing into clutch housing in
conjunction with KM-523-1 (F23)
|
|
|
|
KM-6121
|
Assembly Sleeve
|
|
To secure drive shaft synchromesh body from falling apart
(F23)
|
|
|
|
KM-6122
|
Remover
|
|
To remove drive shaft bearing out of transmission housing in
conjunction with KM-523-1 (F23)
|
|
|
|
KM-6123
|
Remover
|
|
To remove drive shaft bearing out of transmission housing in
conjunction with KM-523-1 (F23)
|
|
|
|
KM-6126
|
Remover
|
|
To remove intermediate shaft out of bearing in conjunction with
KM-523-1 (F23)
|
|
|
|
KM-6127
|
Tool Kit
|
|
To overhaul transmission F23, contains KM-6110 to KM-6123 and
KM-6126 (F23)
|
|
|
|
KM-6146
|
Measurement sleeve
|
|
To measure main shaft in conjunction with KM-621-23 (F23)
|
|
|
|
KM-6155
|
Guide Domes
|
|
Centring the end shield when removing and installing
(F13/F13+/F17/F17+/F18)
|
|
|
|
KM-6173
|
Engine Mount
|
|
Centring the engine when removing the transmission
(F13/F13+/F17/F18/F23/F35)
|
|
|
|
MKM-6174-A
|
Bleeding device
|
|
Bleeding clutch actuation in conjunction with brake bleeding
tool (F13/F13+/F17/F18/F23/F35)
|
|
|
|
KM-6219
|
Pressure sleeve
|
|
Pressing on of Gears, Main and Intermediate Shafts (F23)
|
|
|
|
KM-6220
|
Drift
|
|
Pressing off of Main and Drive Shafts from Gears (F23)
|
|
|
|
KM-6221
|
Mount
|
|
Intermediate shaft mount for pressing out intermediate shaft
(F23)
|
|
|
|
KM-6222
|
Mount
|
|
Drive shaft mount for pressing out drive shaft (F23)
|
|
|
|
KM-6223
|
Mount
|
|
Main shaft mount for pressing out main shaft (F23)
|
|
|
|
KM-6224
|
Mount
|
|
Main shaft mount for pressing out main shaft in conjunction with
KM-6223-1 (F23)
|
|
|
|
KM-6263
|
Remover / Installer
|
|
To secure complete clutch, to remove clutch, to centre the
clutch discs for installation.
|
|
|
|
KM-6335
|
Thrust piece
|
|
Pressing the transmission shaft out of the end shield (F17
new/F17+)
|
|
|
|
KM-6336
|
Installer
|
|
Pressing transmission shaft bearing into end shield with
KM-523-1 (F17 new/F17+)
|
|
|
|
KM-6337
|
Installer
|
|
Pressing in the transmission shafts with KM-6338, supporting the
transmission shafts when pressing on the main shaft sleeve with
KM-6339 (F17 new/F17+)
|
|
|
|
KM-6338
|
Installer
|
|
Supporting the bearings when pressing in the transmission
shafts, with KM-6337 (F17 new/F17+)
|
|
|
|
KM-6339
|
Installer
|
|
Pressing the sleeve on to the main transmission shaft,
supporting with KM-6337 (F17 new/F17+)
|
|
|
|
MKM-6600-100
|
Push-in torx wrench set
|
|
Size: E8, E10, E11, E12, E14, E16, E18, E20, E22, E24, for use
where space is limited, together with MKM-6600-1 and MKM-6600-2
|
|
|
|
MKM-6600-200
|
Push-in box wrench set
|
|
Size: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27,
for use where space is limited, together with MKM-6600-1 and
MKM-6600-2
|
|
|
|
MKM-6600-300
|
Push-in open-end wrench set
|
|
Size: 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27,
for use where space is limited, together with MKM-6600-1 and
MKM-6600-2
|
|
|
|
KM-J-7004
|
Bumping hammer
|
|
Pull gasket for shifter rod out of clutch housing using KM-870
and KM-881(F35)
|
|
|
|
KM-J-8092
|
Insertion mandrel
|
|
Outer race for main shaft roller bearing in transmission housing
in conjunction with KM-743 (F18/F35)
|
|
|
|
KM-J-26938
|
Installer
|
|
Press out outer race of tapered roller bearing for main shaft
using KM-J-8092 (F35)
|
|
|
|
KM-J-26941
|
Remover
|
|
To pull outer sleeve for main shaft bearing out of transmission
housing with KM-313 and KM-483 (F18)
|
|
|
|
KM-J-37228
|
Disconnector
|
|
To remove transmission housing cover from transmission housing
(F23)
|
|
|
|
DT-47648
|
Transmission mount
|
|
Remove, install and hold transmission
|
|
|
1 ) No longer available.
2 ) Only available while stocks last.
|
