Test
|
Work Order Description
|
Nominal Value
|
T001
|
Check: Short to Voltage/Ground/Interruption of Voltage Supply
|
- Ignition OFF
- Disconnect wiring harness connector from:
B18 Sensor - Pressure, Air Conditioning
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & Ground
|
4.8 ... 5.2 V
|
|
|
T002
|
Check: Short to Voltage/Interruption of Ground Circuit
|
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 1 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2
|
4.8 ... 5.2 V
|
|
|
T003
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 17 DTL Z 17 DTH
|
|
|
T004
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System EDC 16C9, Z 17 DTL, Z 17 DTH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T005
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System EDC 16C9, Z 17 DTL, Z 17 DTH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T006
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Check the following component for proper operation:
Fuse of the fused jumper wire
|
Test okay?
|
|
T007
|
Check: Interruption of Signal Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Measure resistance between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3 & A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP) 39 (XC2)
(Z 16 XEP) 4 (XC10)
(Z 18 XE) 7 (XC4)
(Z 20 LEL) (Z 20 LER) (Z 20 LEH) 39 (XC8)
(Z 17 DTL) (Z 17 DTH) 13 (XC12)
(Z 19 DTH) (Z 19 DT) (Z 19 DTL) 13 (XC53)
(Z 13 DTH) 87 (XC20)
(Z 18 XER) 56 (XC4)
(Z 16 XE1) 4 (XC10)
(Z 16 XER) 56 (XC100)
(Z 16 LET) (A 16 LET) 39 (XC98)
(Z 17 DTR) (Z 17 DTJ) (A 17 DTJ) (A 17 DTR) 29 (XC96)
(Z 22 YH) 59 (XC55)
|
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP)
less than 5 Ohm
(Z 16 XEP)
less than 5 Ohm
(Z 18 XE)
less than 5 Ohm
(Z 20 LEL) (Z 20 LER) (Z 20 LEH)
less than 5 Ohm
(Z 17 DTL) (Z 17 DTH)
less than 5 Ohm
(Z 19 DTH) (Z 19 DT) (Z 19 DTL)
less than 5 Ohm
(Z 13 DTH)
less than 5 Ohm
(Z 18 XER)
less than 5 Ohm
(Z 16 XE1)
less than 5 Ohm
(Z 16 XER)
less than 5 Ohm
(Z 16 LET) (A 16 LET)
less than 5 Ohm
(Z 17 DTR) (Z 17 DTJ) (A 17 DTJ) (A 17 DTR)
less than 5 Ohm
(Z 22 YH)
less than 5 Ohm
|
|
|
T008
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Astra-H, Electronic Climate Control ECC Astra-H, Automatic Climate Control SAC
|
|
|
T009
|
Check: Short to Ground of Signal Circuit
|
- Remove fused jumper wire
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Measure resistance between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3 & Ground
|
greater than 500 kOhm
|
|
|
T010
|
Check: Short to Voltage of Signal Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3 & Ground
|
less than 0.3 V
|
|
|
T011
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 14 XEP Z 14 XEL Z 12 XEP
|
|
|
T012
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.1. Z 12 XEP, Z 14 XEP, Z 14 XEL
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T013
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.1. Z 12 XEP, Z 14 XEP, Z 14 XEL
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T014
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 XEP Z 16 XE1
|
|
|
T015
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Multec S (F), Z 16 XEP, Z 16 XE1
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T016
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Multec S (F), Z 16 XEP, Z 16 XE1
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T017
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 18 XE
|
|
|
T018
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Simtec 71.6, Z 18 XE
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T019
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Simtec 71.6, Z 18 XE
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T020
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 20 LEL Z 20 LER Z 20 LEH
|
|
|
T021
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.1, Z 20 LEH, Z 20 LEL, Z 20 LER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T022
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.1, Z 20 LEH, Z 20 LEL, Z 20 LER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T023
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 19 DTH Z 19 DT Z 19 DTL
|
|
|
T024
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System EDC 16C9/16C39, Z 19 DT, Z 19 DTH, Z 19 DTL
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T025
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System EDC 16C9/16C39, Z 19 DT, Z 19 DTH, Z 19 DTL
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T026
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 13 DTH
|
|
|
T027
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System Multijet 6JO, Z 13 DTH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T028
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System Multijet 6JO, Z 13 DTH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T029
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 18 XER
|
|
|
T030
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Simtec 75, Z 18 XER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T031
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Simtec 75, Z 18 XER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T032
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 XER
|
|
|
T033
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Simtec 75, Z 16 XER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T034
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Simtec 75, Z 16 XER
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T035
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 LET A 16 LET
|
|
|
T036
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.2, A 16 LET, Z 16 LET
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T037
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Motronic 7.6.2, Z 16 LET
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T038
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 17 DTR Z 17 DTJ
|
|
|
T039
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System DECE1C, A 17 DTJ, A 17 DTR, Z 17 DTJ, Z 17 DTR
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T040
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Electronic Diesel Injection System DECE1C, A 17 DTJ, A 17 DTR, Z 17 DTJ, Z 17 DTR
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T041
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 22 YH
|
|
|
T042
|
Check: Short to Voltage of Signal Circuit
|
- Select the following Functional System on the diagnostic tester:
Simtec 81, Z 22 YH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
less than 0.3 V
|
|
|
T043
|
Check: Short to Ground/Interruption of Signal Circuit
|
- Connect fused jumper wire to:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 3
- Select the following Functional System on the diagnostic tester:
Simtec 81, Z 22 YH
- Diagnostic Tester Data List Parameter
A/C Pressure (Air Conditioning)
|
greater than 4.8 V
|
|
|
T044
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 17 DTL Z 17 DTH Z 17 DTJ Z 17 DTR A 17 DTJ A 17 DTR
|
|
|
T045
|
Check: Circuit Interruption of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal
(Z 16 XEP) 34 (XC10)
(Z 18 XE) 34 (XC4)
(Z 17 DTL) (Z 17 DTH) 12 (XC12)
(Z 19 DTH) (Z 19 DT) (Z 19 DTL) 12 (XC53)
(Z 13 DTH) 10 (XC20)
(Z 18 XER) 39 (XC4)
(Z 16 XE1) 34 (XC10)
(Z 16 XER) 39 (XC100)
(Z 17 DTJ) (Z 17 DTR) (A 17 DTJ) (A 17 DTR) 16 (XC96)
(Z 22 YH) 11 (XC55)
& B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 1
|
(Z 16 XEP)
less than 5 Ohm
(Z 18 XE)
less than 5 Ohm
(Z 17 DTL) (Z 17 DTH)
less than 5 Ohm
(Z 19 DTH) (Z 19 DT) (Z 19 DTL)
less than 5 Ohm
(Z 13 DTH)
less than 5 Ohm
(Z 18 XER)
less than 5 Ohm
(Z 16 XE1)
less than 5 Ohm
(Z 16 XER)
less than 5 Ohm
(Z 17 DTJ) (Z 17 DTR) (A 17 DTJ) (A 17 DTR)
less than 5 Ohm
(Z 22 YH)
less than 5 Ohm
|
|
|
T046
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 13 DTH
|
|
|
T047
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 16 XEP Z 16 XE1 Z 16 XER
|
|
|
T048
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 18 XE Z 18 XER Z 22 YH
|
|
|
T049
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 19 DTH Z 19 DT Z 19 DTL
|
|
|
T050
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 14 XEP Z 14 XEL Z 12 XEP Z 16 LET A 16 LET
|
|
|
T051
|
Check: Short to Voltage/Interruption of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B22 Sensor - Pedal Position
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 1 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2
|
4.8 ... 5.2 V
|
|
|
T052
|
Check: Circuit Interruption of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP) 5 (XC2)
(Z 20 LEL) (Z 20 LER) (Z 20 LEH) 5 (XC8)
(Z 16 LET) (A 16 LET) 5 (XC98)
& B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 1
|
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP)
less than 5 Ohm
(Z 20 LEL) (Z 20 LER) (Z 20 LEH)
less than 5 Ohm
(Z 16 LET) (A 16 LET)
less than 5 Ohm
|
|
|
T053
|
Check: Vehicle Configuration
|
Is the following information correct for the actual vehicle?
Z 20 LEL Z 20 LER Z 20 LEH
|
|
|
T054
|
Check: Short to Voltage/Interruption of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B22 Sensor - Pedal Position
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 1 & B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2
|
4.8 ... 5.2 V
|
|
|
T055
|
Check: Short to Voltage/Ground/Interruption of Voltage Supply
|
- Ignition OFF
- Disconnect wiring harness connector from:
B18 Sensor - Pressure, Air Conditioning
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & Ground
|
greater than 5.2 V
|
|
|
T056
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Ignition ON
- Measure voltage between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & Ground
|
less than 0.3 V
|
|
|
T057
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine
- Measure resistance between the following terminals:
B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal 2 & Ground
|
greater than 500 kOhm
|
|
|
T058
|
Check: Interruption of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP) 53 (XC2)
(Z 16 XEP) 3 (XC10)
(Z 18 XE) 23 (XC4)
(Z 20 LEL) (Z 20 LER) (Z 20 LEH) 53 (XC8)
(Z 17 DTH) (Z 17 DTL) 22 (XC12)
(Z 19 DTH) (Z 19 DT) (Z 19 DTL) 22 (XC53)
(Z 13 DTH) 37 (XC20)
(Z 18 XER) 23 (XC4)
(Z 16 XE1) 3 (XC10)
(Z 16 XER) 23 (XC100)
(Z 16 LET) (A 16 LET) 53 (XC98)
(Z 17 DTR) (Z 17 DTJ) (A 17 DTJ) (A 17 DTR) 42 (XC96)
(Z 22 YH) 35 (XC55)
& B18 Sensor - Pressure, Air Conditioning Wiring harness connector (wiring harness side) terminal
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP) 2
(Z 16 XEP) 2
(Z 18 XE) 2
(Z 20 LEL) (Z 20 LER) (Z 20 LEH) 2
(Z 17 DTH) (Z 17 DTL) 2
(Z 19 DTH) (Z 19 DT) (Z 19 DTL) 2
(Z 13 DTH) 2
(Z 18 XER) 2
(Z 16 XE1) 2
(Z 16 XER) 2
(Z 16 LET) (A 16 LET) 2
(Z 17 DTR) (Z 17 DTJ) (A 17 DTJ) (A 17 DTR) 2
(Z 22 YH) 5
|
(Z 14 XEL) (Z 14 XEP) (Z 12 XEP)
less than 5 Ohm
(Z 16 XEP)
less than 5 Ohm
(Z 18 XE)
less than 5 Ohm
(Z 20 LEL) (Z 20 LER) (Z 20 LEH)
less than 5 Ohm
(Z 17 DTH) (Z 17 DTL)
less than 5 Ohm
(Z 19 DTH) (Z 19 DT) (Z 19 DTL)
less than 5 Ohm
(Z 13 DTH)
less than 5 Ohm
(Z 18 XER)
less than 5 Ohm
(Z 16 XE1)
less than 5 Ohm
(Z 16 XER)
less than 5 Ohm
(Z 16 LET) (A 16 LET)
less than 5 Ohm
(Z 17 DTR) (Z 17 DTJ) (A 17 DTJ) (A 17 DTR)
less than 5 Ohm
(Z 22 YH)
less than 5 Ohm
|
|
|