Test
|
Work Order Description
|
Nominal Value
|
T001
|
Check: Short to Voltage/Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B36BL Sensor - Vertical Acceleration Body, Front Left
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
|
4.5 ... 5.5 V
|
|
|
T002
|
Check: Short to Voltage of Ground Circuit
|
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 3 & Ground
|
less than 0.3 V
|
|
|
T003
|
Check: Short to Voltage of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B36BR Sensor - Vertical Acceleration Body, Front Right
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 3 & Ground
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
B36WL Sensor - Vertical Acceleration Wheel, Front Left B36WR Sensor - Vertical Acceleration Wheel, Front Right B37 Sensor - Vertical Acceleration Body, Rear
|
less than 0.3 V
|
|
|
T004
|
Check: Short to Voltage of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A6 Control Unit - Semi Active Damping System
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 3 & Ground
|
less than 0.3 V
|
|
|
T005
|
Check: Short to Voltage of Ground Circuit
|
- Measure voltage between the following terminals:
A6 Control Unit - Semi Active Damping System Wiring harness connector (wiring harness side) terminal 25 & Ground
|
less than 0.3 V
|
|
|
T006
|
Check: Short to Voltage/Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B36BL Sensor - Vertical Acceleration Body, Front Left
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
|
less than 4.5 V
|
|
|
T007
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A6 Control Unit - Semi Active Damping System
- Measure resistance between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
|
greater than 500 kOhm
|
|
|
T008
|
Check: Short to Ground of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
A6 Control Unit - Semi Active Damping System Wiring harness connector (wiring harness side) terminal 30 & Ground
|
greater than 500 kOhm
|
|
|
T009
|
Check: Short to Ground of Voltage Supply Circuit
|
- Disconnect wiring harness connector from:
B36BR Sensor - Vertical Acceleration Body, Front Right
- Measure resistance between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
B36WL Sensor - Vertical Acceleration Wheel, Front Left B36WR Sensor - Vertical Acceleration Wheel, Front Right
|
greater than 500 kOhm
|
|
|
T010
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B36BR Sensor - Vertical Acceleration Body, Front Right
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
B36WL Sensor - Vertical Acceleration Wheel, Front Left B36WR Sensor - Vertical Acceleration Wheel, Front Right B37 Sensor - Vertical Acceleration Body, Rear
|
less than 5.5 V
|
|
|
T011
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A6 Control Unit - Semi Active Damping System
- Ignition ON
- Measure voltage between the following terminals:
B36BL Sensor - Vertical Acceleration Body, Front Left Wiring harness connector (wiring harness side) terminal 1 & Ground
|
less than 0.3 V
|
|
|
T012
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Measure voltage between the following terminals:
- A6 Control Unit - Semi Active Damping System
Wiring harness connector (wiring harness side) terminal 30 & Ground
|
less than 0.3 V
|
|
|