vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
B-003 Diagnostic System Check > < B-001 DIAGNOSTIC TROUBLE CODE

Astra H

B-002 - DATA LIST

Test

Work Order Description

Nominal Value
T001 Tester Display Battery Voltage
  • Ignition ON
  • Engine OFF
  • All consumers turned off
11 ... 13.5 V
  • Engine starting
greater than 8 V
  • Engine running at idle speed, operating temperature
  • All consumers turned off
12 ... 15 V
Concerned Terminals:
ECM: 19 (XC53)
  
Yes: No:
T002 Tester Display Fuel Pump Relay
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Wait at least 20 s
Inactive
  • Engine running at idle speed, operating temperature
Active
Concerned Terminals:
ECM: 20 (XC53)
  
Yes: No:
T003 Tester Display APP at Idle Position (Accelerator Pedal Position)
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated
Active
  • Accelerator pedal slightly actuated
Inactive
  • Accelerator pedal actuated to full load stop
Inactive
Concerned Terminals:
ECM: 8, 9, 30, 31, 45, 46 (XC53)
  
Yes: No:
T004 Tester Display APP Sensor 1 (Accelerator Pedal Position)
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated
less than 1 V
  • Accelerator pedal slightly actuated
greater than 1 V
  • Accelerator pedal actuated to full load stop
greater than 3 V
Concerned Terminals:
ECM: 8, 9, 30, 31, 45, 46 (XC53)
  
Yes: No:
T005 Tester Display APP Sensor 2 (Accelerator Pedal Position)
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated
less than 0.5 V
  • Accelerator pedal slightly actuated
greater than 0.5 V
  • Accelerator pedal actuated to full load stop
greater than 1.5 V
Concerned Terminals:
ECM: 8, 9, 30, 31, 45, 46 (XC53)
  
Yes: No:
T006 Tester Display Calculated Pedal Position
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Accelerator pedal not actuated
0 %
  • Accelerator pedal actuated to full load stop
greater than 90 %
Concerned Terminals:
ECM: 8, 9, 30, 31, 45, 46 (XC53)
  
Yes: No:
T007 Tester Display Desired Engine Idle Speed
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
(Z 19 DT)
750 ... 850 rpm
(Z 19 DTL)
750 ... 850 rpm
(Z 19 DTH)
800 ... 900 rpm
Concerned Terminals:
ECM: 12, 27 (XC52)
  
Yes: No:
T008 Tester Display Engine Speed
  • Engine starting
greater than 60 rpm
Concerned Terminals:
ECM: 12, 27 (XC52)
  
Yes: No:
T009 Tester Display Camshaft Speed
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  
(Z 19 DT)
375 ... 425 RPM.
(Z 19 DTL)
375 ... 425 RPM.
(Z 19 DTH)
400 ... 450 RPM.
Concerned Terminals:
ECM: 11, 20, 50 (XC52)
  
Yes: No:
T010 Tester Display Idle Speed Modified
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

Default value after reset of programmed desired idle speed
No
  • Accelerator pedal not actuated

Note:

Desired idle speed has been programmed
Yes
Concerned Terminals:
ECM: 12, 27 (XC52)
  
Yes: No:
T011 Tester Display Calculated Air Flow
  • Ignition ON
0 kg/h
  • Engine running at idle speed, operating temperature
  • Exhaust gas recirculation valve closed
  • Accelerator pedal not actuated
20 ... 35 kg/h
  • All consumers turned off
  • Accelerator pedal actuated several times
Value changing briefly
Concerned Terminals:
ECM: 42, 44 (XC52)
  
Yes: No:
T012 Tester Display Charge Air Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
10 ... 120 °C
50 ... 248 °F
4.50 ... 0.12 V
Concerned Terminals:
ECM: 13, 23, 53 (XC52)
  
Yes: No:
T013 Tester Display Ambient Temperature
  • Ignition ON
  • Engine OFF
  • All consumers turned off
Diagnostic tester display converges to outside temperature
Concerned Terminals:
-
  
Yes: No:
T014 Tester Display Mass Air Flow Sensor
  • Ignition ON
-2 ... 3 kg/h
  • Engine running at idle speed, operating temperature
  • Exhaust gas recirculation valve open
  • Accelerator pedal not actuated
20 ... 35 kg/h
  • All consumers turned off
  • Accelerator pedal actuated several times
Value changing briefly
Concerned Terminals:
ECM: 42, 44 (XC52)
  
Yes: No:
T015 Tester Display Coolant Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
80 ... 110 °C
176 ... 230 °F
2.50 ... 0.40 V
Concerned Terminals:
ECM: 41, 58 (XC52)
  
Yes: No:
T016 Tester Display Fuel Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
10 ... 120 °C
50 ... 248 °F
4.50 ... 0.12 V
Concerned Terminals:
ECM: 10, 11 (XC53)
  
Yes: No:
T017 Tester Display Oil Level
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

Check Engine Oil Level
Normal
Concerned Terminals:
ECM: 21 (XC52)
  
Yes: No:
T018 Tester Display Oil Pressure
  • Ignition ON
  • Engine running at idle speed
Normal
Concerned Terminals:
ECM: 56 (XC 52)
  
Yes: No:
T019 Tester Display Engine Oil Level Status
  • Ignition ON
  • Engine OFF
  • All consumers turned off

Note:

Check Engine Oil Level
Okay
Concerned Terminals:
ECM: 21 (XC52)
  
Yes: No:
T020 Tester Display Barometric Pressure
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Compare displayed pressure with outside-air pressure
80 ... 120 kPa
3.2 ... 4.8 V
Diagnostic tester display is nearly identical to outside-air pressure
Concerned Terminals:
-
  
Yes: No:
T021 Tester Display Boost Pressure Command
  • Ignition ON
  • Engine OFF
  • All consumers turned off
90 ... 120 kPa
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
90 ... 120 kPa
  • Accelerator pedal slightly actuated

Note:

Increase engine speed to 3000 rpm
100 ... 230 kPa
Concerned Terminals:
ECM: 13, 23, 40 (XC52)
  
Yes: No:
T022 Tester Display Boost Pressure
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Compare displayed pressure with outside-air pressure
90 ... 120 kPa
1.50 ... 2.50 V
Diagnostic tester display is nearly identical to outside-air pressure
  • Engine running at idle speed, operating temperature
  • Accelerator pedal not actuated
90 ... 120 kPa
1.50 ... 2.50 V
  • Accelerator pedal slightly actuated

Note:

To build up boost pressure, the engine should be operated above 3000 rpm and with a high load.
100 ... 230 kPa
1.60 ... 4.50 V
Concerned Terminals:
ECM: 13, 23, 40 (XC52)
  
Yes: No:
T023 Tester Display Pulse Ratio Boost Pressure Solenoid Valve
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
70 ... 80 %
  • Accelerator pedal actuated several times
less than 70 %
Value changing briefly
Concerned Terminals:
ECM: 15 (XC52)
  
Yes: No:
T024 Tester Display EGR Position Commanded (Exhaust Gas Recirculation)
  • Ignition ON
greater than 90 %
  • Engine running at idle speed, operating temperature
  • Exhaust gas recirculation valve open
  • Accelerator pedal not actuated
less than 90 %
  • All consumers turned off
  • Accelerator pedal actuated several times
Value changing briefly
  • Accelerator pedal not actuated
  • Wait at least 70 s
greater than 90 %
Concerned Terminals:
ECM: 60 (XC52)
  
Yes: No:
T025 Tester Display EGR Pulse Ratio (Exhaust Gas Recirculation)
  • Ignition ON
less than 10 %
  • Engine running at idle speed, operating temperature
  • Exhaust gas recirculation valve open
  • Accelerator pedal not actuated
greater than 10 %
  • All consumers turned off
  • Accelerator pedal actuated several times
Value changing briefly
  • Accelerator pedal not actuated
  • Wait at least 70 s
less than 10 %
Concerned Terminals:
ECM: 60 (XC52)
  
Yes: No:
T026 Tester Display Swirl Level Control Solenoid Valve Pulse Ratio
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
(Z 19 DTH)
3 ... 97 %
(Z 19 DTL) (Z 19 DT)
The data list parameter is invalid for this configuration
  • Accelerator pedal actuated several times
Value changing briefly
Concerned Terminals:
ECM: 6, 35, 45 (XC52)
  
Yes: No:
T027 Tester Display Swirl Actuator Feedback
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
less than 500 ms
Concerned Terminals:
ECM: 6, 35, 45 (XC52)
  
Yes: No:
T028 Tester Display Throttle Position Sensor Signal
  • Ignition ON
  • Engine OFF
  • All consumers turned off
greater than 5 %
Concerned Terminals:
ECM: 39, 52, 59 (XC52)
  
Yes: No:
T029 Tester Display Throttle Position PWM Servo Signal
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
5 ... 95 %
  • Engine OFF
95 ... 97 %
Value changing briefly
Concerned Terminals:
ECM: 39, 52, 59 (XC52)
  
Yes: No:
T030 Tester Display Desired Common Rail Fuel Pressure
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
20 ... 50 MPa
Concerned Terminals:
ECM: 8, 28, 43 (XC52)
  
Yes: No:
T031 Tester Display Common Rail Fuel Pressure
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
20 ... 50 MPa
0.70 ... 2.10 V
  • Accelerator pedal actuated several times
20 ... 150 MPa
0.70 ... 4.50 V
Concerned Terminals:
ECM: 8, 28, 43 (XC52)
  
Yes: No:
T032 Tester Display Rail Pressure Control Solenoid Valve PWM
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
Default
The data list parameter is invalid for this configuration
(Fuel Pressure Regulator is mounted to Common Rail)
20 ... 45 %
Concerned Terminals:
ECM: 4, 34 (XC52)
  
Yes: No:
T033 Tester Display Rail Pressure Control Solenoid Valve Current
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
Default
The data list parameter is invalid for this configuration
(Fuel Pressure Regulator is mounted to Common Rail)
0.6 ... 1.0 A
Concerned Terminals:
ECM: 4, 34 (XC52)
  
Yes: No:
T034 Tester Display Fuel Metering Solenoid Valve PWM
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
30 ... 50 %
Concerned Terminals:
ECM: 19, 49 (XC52)
  
Yes: No:
T035 Tester Display Fuel Metering Solenoid Valve Current
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
1.20 ... 1.65 A
Concerned Terminals:
ECM: 19, 49 (XC52)
  
Yes: No:
T036 Tester Display B1S1 O2 Sensor Heater Temperature
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

Wait at least 5 min

After approximately 5 min

Value is increasing

  
(O2 Sensor)
1300 ... 250 °C
2372 ... 482 °F
(Diesel Particulate Filter)
The data list parameter is invalid for this configuration
Concerned Terminals:
ECM: 51 (XC53)
  
Yes: No:
T037 Tester Display B1S1 O2 Sensor Heater PWM
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

120 s elapsed time since engine start

  
(O2 Sensor)
100 ... 0 %
(Diesel Particulate Filter)
The data list parameter is invalid for this configuration
Concerned Terminals:
ECM: 51 (XC53)
  
Yes: No:
T038 Tester Display B1S1 O2 Sensor (Bank 1 Sensor 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated

Note:

120 s elapsed time since engine start

  
(O2 Sensor)
3000 ... 0 mV
(Diesel Particulate Filter)
The data list parameter is invalid for this configuration
Concerned Terminals:
ECM: 64, 65, 86, 87 (XC53)
  
Yes: No:
T039 Tester Display B1S1 Exhaust Gas Temperature (Bank 1 Sensor 1)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
(Diesel Particulate Filter)
30 ... 300 °C
86 ... 572 °F
0.8 ... 1.5 V
(O2 Sensor)
Data list parameter will not be displayed for selected vehicle configuration
Concerned Terminals:
ECM: 34, 35 (XC53)
  
Yes: No:
T040 Tester Display B1S2 Exhaust Gas Temperature (Bank 1 Sensor 2)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
(Diesel Particulate Filter)
30 ... 250 °C
86 ... 482 °F
0.8 ... 1.3 V
(O2 Sensor)
Data list parameter will not be displayed for selected vehicle configuration
Concerned Terminals:
ECM: 32, 33 (XC53)
  
Yes: No:
T041 Tester Display Differential Pressure Diesel Particulate Filter
  • Ignition ON
  
(Diesel Particulate Filter)
-1 ... 1 kPa
0.48 ... 1.20 V
(O2 Sensor)
Data list parameter will not be displayed for selected vehicle configuration
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
0 ... 100 kPa
0.49 ... 1.20 V
Concerned Terminals:
ECM: 36, 37, 44 (XC53)
  
Yes: No:
T042 Tester Display Diesel Particulate Filter Saturation
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  
(Diesel Particulate Filter)
less than 110 %
(O2 Sensor)
Data list parameter will not be displayed for selected vehicle configuration
Concerned Terminals:
-
  
Yes: No:
T043 Tester Display A/C Information Switch (Air Conditioning)
  • Engine idling
  • All consumers turned off
  • Air conditioning system switch OFF
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Inactive
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
Inactive
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
The data list parameter is invalid for this configuration
(Automatic Climate Control SAC)
Inactive
  • Air conditioning system switch ON
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Active
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
Active
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
The data list parameter is invalid for this configuration
(Automatic Climate Control SAC)
Active
Concerned Terminals:
-
  
Yes: No:
T044 Tester Display A/C Pressure (Air Conditioning)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
Default
0 kPa
The data list parameter is invalid for this configuration
(Astra-H), (Air Conditioning (not ECC))
320 ... 3100 kPa
(Astra-H), (Electronic Climate Control ECC)
320 ... 3100 kPa
(Automatic Climate Control SAC)
320 ... 3100 kPa
  • Air conditioning system switch ON
  
Default
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Is there a pressure difference of at least 500 kPa ?
(Electronic Climate Control ECC)
Is there a pressure difference of at least 500 kPa ?
(Automatic Climate Control SAC)
Is there a pressure difference of at least 500 kPa ?
Concerned Terminals:
ECM: 12, 13, 22 (XC53)
  
Yes: No:
T045 Tester Display A/C Cutoff Mode (Air Conditioning)
  • Engine idling
  • Coolant temperature between 60 °C (140 °F) and 115 °C (239 °F)
  • Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 3100 kPa ( 31 bar )
  • Accelerator pedal not actuated
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
System OK
(Electronic Climate Control ECC)
System OK
(Automatic Climate Control SAC)
System OK
Concerned Terminals:
ECM: 29 (XC53)
  
Yes: No:
T046 Tester Display A/C Relay (Air Conditioning)
  • Engine running at idle speed, operating temperature
  • All consumers turned off
  • Accelerator pedal not actuated
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Inactive
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
Inactive
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
The data list parameter is invalid for this configuration
(Automatic Climate Control SAC)
Inactive
  • Air conditioning system switch ON
  
Default
Not Programmed
The data list parameter is invalid for this configuration
(Air Conditioning (not ECC))
Active
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
Active
(Automatic Climate Control SAC)
Active
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
The data list parameter is invalid for this configuration
Concerned Terminals:
ECM: 29 (XC53)
  
Yes: No:
T047 Tester Display Brake Switch 1
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Brake pedal not actuated
Inactive
  • Brake pedal actuated
Active
Concerned Terminals:
ECM: 17, 80 (XC53)
  
Yes: No:
T048 Tester Display Brake Switch 2
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Brake pedal not actuated
Inactive
  • Brake pedal actuated
Active
Concerned Terminals:
ECM: 17, 80 (XC53)
  
Yes: No:
T049 Tester Display Clutch Switch
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Do not actuate clutch pedal
  
(Front Wheel Drive, Automatic Transmission, AF 40-6)
The data list parameter is invalid for this configuration
(Front Wheel Drive, Manual Transmission)
Inactive
  • Clutch pedal actuated
  
(Front Wheel Drive, Manual Transmission)
Active
(Front Wheel Drive, Automatic Transmission, AF 40-6)
The data list parameter is invalid for this configuration
Concerned Terminals:
ECM: 79 (XC53)
  
Yes: No:
T050 Tester Display Park/Neutral Switch
  • Ignition ON
  • Engine OFF
  • Selector lever in position P / N
  
(Front Wheel Drive, Automatic Transmission, AF 40-6)
P - N
(Front Wheel Drive, Manual Transmission)
The data list parameter is invalid for this configuration
  • Selector lever in position R / D
  
(Front Wheel Drive, Automatic Transmission, AF 40-6)
R - D
(Front Wheel Drive, Manual Transmission)
The data list parameter is invalid for this configuration
Concerned Terminals:
-
  
Yes: No:
T051 Tester Display Vehicle Speed
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
Diagnostic tester display is nearly identical to actual vehicle speed
Concerned Terminals:
-
  
Yes: No:
T052 Tester Display Vehicle Speed in Cruise Control Range
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
  
Default
Not Programmed
(Electronic Cruise Control)
Active
Concerned Terminals:
-
  
Yes: No:
T053 Tester Display Cruise Control Tip Switch
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Key " I " pressed
  
Default
Not Programmed
(Electronic Cruise Control)
I (set)
  • Key " R " pressed
  
Default
Not Programmed
(Electronic Cruise Control)
R (Resume)
  • Key " O " pressed
  
Default
Not Programmed
(Electronic Cruise Control)
O (off)
Concerned Terminals:
-
  
Yes: No:
T054 Tester Display Cruise Control
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  
Default
Not Programmed
(Electronic Cruise Control)
Inactive
  • Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
  • Key " I " pressed (for longer than 0.5 s )
Active
Concerned Terminals:
-
  
Yes: No:
T055 Tester Display Glow Time Relay
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Glow plug activated
Active 0V
  • Glow plug deactivated
Inactive 12V
Concerned Terminals:
ECM: 52, 93 (XC53)
  
Yes: No:
T056 Tester Display Diagnosis Glow Time Relay
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Glow plug activated
Active
  • Glow plug deactivated
Inactive
Concerned Terminals:
ECM: 52, 93 (XC53)
  
Yes: No:
T057 Tester Display Glow Time Telltale
  • Ignition ON
  • Engine OFF
  • All consumers turned off
  • Glow time telltale ON
On 0V
  • Glow time telltale OFF
Off 12V
Concerned Terminals:
-
  
Yes: No:





B-003 Diagnostic System Check > < B-001 DIAGNOSTIC TROUBLE CODE