vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-008 Crankshaft Sensor Circuit > < C-006 5V Circuit 2

Astra H

C-007 - 5V Circuit 3

Test

Work Order Description

Nominal Value
T001

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Air Conditioning (not ECC)
Astra-H, Electronic Climate Control ECC
Astra-H, Automatic Climate Control SAC
Yes: No:
T002

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B18 Sensor - Pressure, Air Conditioning
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P1639 with status PRESENT stored?
Yes: No:
T003

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Diesel Particulate Filter
Yes: No:
T004

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B175 Sensor - Pressure, Exhaust Gas
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P1639 with status PRESENT stored?
Yes: No:
T005

Check: Component
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B22 Sensor - Pedal Position
  • Ignition ON
  • Trouble Code Update

Is the diagnostic trouble code P1639 with status PRESENT stored?
Yes: No:
T006

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Air Conditioning (not ECC)
Astra-H, Electronic Climate Control ECC
Astra-H, Automatic Climate Control SAC
Yes: No:
T007

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC20 )
    Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T008

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC20)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T009

Check: Short to Voltage of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC20 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T010

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC20)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T011

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Diesel Particulate Filter
Yes: No:
T012

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 14 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T013

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 14 (XC20)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T014

Check: Short to Ground of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2 )
  • Measure resistance between the following terminals:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T015

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2 )
  • Ignition ON
  • Measure voltage between the following terminals:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T016

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC20 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T017

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 32 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T018

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2 )
  • Ignition ON
  • Measure voltage between the following terminals:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T019

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2 )
  • Ignition ON
  • Measure voltage between the following terminals:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T020

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC20 )
  • Ignition ON
    Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 49 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T021

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 33 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T022

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC20 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 87 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T023

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 10 (XC20)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E002 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 14 (XC20)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 1
E003 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 14 (XC20)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 1
E004 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 42 (XE3)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E005 Result: Short to Ground
  • Short circuit to ground between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E006 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 15 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 42 (XE3)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E007 Result: Short to Voltage
  • Short circuit to voltage between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E008 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE3)
    or
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E009 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE3)
    or
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E010 Result: Defective Component
  • Defective component:
    B22 Sensor - Pedal Position
    or
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E011 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 43 (XE3)
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 32 (XC20)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E012 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E013 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 41 (XC20)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E014 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E015 Result: Defective Component
  • Defective component:
    B175 Sensor - Pressure, Exhaust Gas
E016 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 33 (XC20)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 2
E017 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 49 (XC20)
    &
    B175 Sensor - Pressure, Exhaust Gas
    Wiring harness connector (wiring harness side) terminal 3
E018 Result: Defective Component
  • Defective component:
    B18 Sensor - Pressure, Air Conditioning
E019 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 10 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 7 (XE3)
    or
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 10 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E020 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 87 (XC20)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 8 (XE3)
    or
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 30 (XE1)
    &
    B18 Sensor - Pressure, Air Conditioning
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.





C-008 Crankshaft Sensor Circuit > < C-006 5V Circuit 2