vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-017 Hydraulic Pump Circuit > < C-015 Shift Position Sensor Circuit

Astra H

C-016 - Select Position Sensor Circuit

Test

Work Order Description

Nominal Value
T001

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B193A Sensor - Select Position
    and
    B193B Sensor - Shift Position
    and
    A112 Control Unit - Transmission
    (Wiring Harness Connector XC83 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T003

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 1

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T004

Check: Short to Voltage of Signal Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T005

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T006

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 2

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T007

Check: Short to Voltage of Signal Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T008

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T009

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 3

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    B193A Sensor - Select Position
    or
    A112 Control Unit - Transmission

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E002 Result: Interruption
  • Circuit interruption between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 3
E003 Result: Short to Ground
  • Short circuit to ground between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 3
E004 Result: Short to Voltage
  • Short circuit to voltage between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 4 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 3
E005 Result: Interruption
  • Circuit interruption between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 2
E006 Result: Short to Ground
  • Short circuit to ground between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 2
E007 Result: Short to Voltage
  • Short circuit to voltage between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 12 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 2
E008 Result: Interruption
  • Circuit interruption between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 1
E009 Result: Short to Ground
  • Short circuit to ground between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 1
E010 Result: Short to Voltage
  • Short circuit to voltage between:
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 6 (XC83)
    &
    B193A Sensor - Select Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    B193B Sensor - Shift Position
    Wiring harness connector (wiring harness side) terminal 1





C-017 Hydraulic Pump Circuit > < C-015 Shift Position Sensor Circuit