|
Test
|
Work Order Description
|
Nominal Value
|
|
T001
|
Tester Display Ignition Status
|
- Ignition OFF
- Remove ignition key from ignition lock
|
Off
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
On
|
Concerned Terminals:
-
|
|
|
|
|
T002
|
Tester Display Car Key In Recognition
|
- Ignition OFF
- Remove ignition key from ignition lock
|
Inactive
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Active 12V
|
Concerned Terminals:
-
|
|
|
|
|
T003
|
Tester Display Outside Temperature
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Diagnostic tester display converges to outside temperature
|
Concerned Terminals:
-
|
|
|
|
|
T004
|
Tester Display Engine Coolant Temperature
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- All cooling fans are switched off
|
Diagnostic tester display converges to engine temperature
|
Concerned Terminals:
UEC: 10 (XE2)
|
|
|
|
|
T005
|
Tester Display Vehicle Speed
|
- Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
|
Diagnostic tester display is nearly identical to actual vehicle speed
|
Concerned Terminals:
-
|
|
|
|
|
T006
|
Tester Display Fuel Level
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
Depending on the vehicle/system configuration it is possible that some data list parameters or test steps, although they are listed in this checking procedure, are not shown on the diagnostic tester display. In that case, these data list parameters are not valid for this vehicle/system configuration.
|
Diagnostic tester display converges to actual fuel tank content
|
Concerned Terminals:
-
|
|
|
|
|
T007
|
Tester Display Rotary EHU Button Status
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
No Key Pressed
|
- Press the following key:
Multi-Function Button
Note:
Depending on the vehicle/system configuration it is possible that some data list parameters or test steps, although they are listed in this checking procedure, are not shown on the diagnostic tester display. In that case, these data list parameters are not valid for this vehicle/system configuration.
|
Diagnostic tester shows the used key
|
Concerned Terminals:
-
|
|
|
|
|
T008
|
Tester Display Set Key
|
|
Only TID :
|
Inactive
|
|
Note:
Depending on the vehicle/system configuration it is possible that some data list parameters or test steps, although they are listed in this checking procedure, are not shown on the diagnostic tester display. In that case, these data list parameters are not valid for this vehicle/system configuration.
|
Active
|
Concerned Terminals:
-
|
|
|
|
|
T009
|
Tester Display Clock Key
|
|
Only TID :
|
Inactive
|
|
Note:
Depending on the vehicle/system configuration it is possible that some data list parameters or test steps, although they are listed in this checking procedure, are not shown on the diagnostic tester display. In that case, these data list parameters are not valid for this vehicle/system configuration.
|
Active
|
Concerned Terminals:
-
|
|
|
|
|
T010
|
Tester Display Right Steering Wheel Remote Control Status
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
No Key Pressed
|
- Any key of the steering wheel remote control pressed
|
Diagnostic tester shows the used key
|
Concerned Terminals:
-
|
|
|
|
|
T011
|
Tester Display Left Steering Wheel Remote Control Status
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
No Key Pressed
|
- Any key of the steering wheel remote control pressed
|
Diagnostic tester shows the used key
|
Concerned Terminals:
-
|
|
|
|
|
T012
|
Tester Display Theft Protection
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
Depending on the vehicle/system configuration it is possible that some data list parameters or test steps, although they are listed in this checking procedure, are not shown on the diagnostic tester display. In that case, these data list parameters are not valid for this vehicle/system configuration.
|
ID O.K.
|
Concerned Terminals:
-
|
|
|
|
