vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-005 Rear Left Window Lifter Circuit > < C-003 Window Lifter, Front Passenger Door Circuit

Astra H

C-004 - Window Lifter, Switch Rear Left Circuit

Test

Work Order Description

Nominal Value
T001

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Do not actuate the following switch:
    S115.5 Switch - Child Security
    (Child Security inactive)
  • Disconnect wiring harness connector from:
    S221RL Switch - Window Lifter, Rear Door, Left
  • Ignition ON
  • Measure voltage between the following terminals:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    6 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T003

Check: Short to Voltage of Signal Circuit
  • Measure voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T004

Check: Short to Voltage of Signal Circuit
  • Measure voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T005

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Measure resistance between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T006

Check: Short to Ground of Signal Circuit
  • Measure resistance between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T007

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M14L Motor - Window Lifter, Rear Door, Left
  • Ignition ON
  • Measure voltage between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T008

Check: Circuit Interruption of Ground Circuit
  • Measure voltage between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 4

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T009

Check: Short to Voltage of Signal Circuit
  • Measure voltage between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T010

Check: Short to Voltage of Signal Circuit
  • Measure voltage between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T011

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Connect wiring harness connector to:
    M14L Motor - Window Lifter, Rear Door, Left
  • Ignition ON
  • Connect fused jumper wire for a maximum of 2 s to:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
  • The corresponding motor tries to move in DOWN direction

Test okay?
Yes: No:
T012

Check: Short to Ground of Signal Circuit
  • Connect fused jumper wire for a maximum of 2 s to:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
  • The corresponding motor tries to move in UP direction

Test okay?
Yes: No:
T013

Check: Short to Ground of Signal Circuit
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T014

Check: Interruption of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M14L Motor - Window Lifter, Rear Door, Left
  • Measure resistance between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T015

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    6 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T016

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    4 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T017

Check: Short to Ground of Signal Circuit
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T018

Check: Interruption of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M14L Motor - Window Lifter, Rear Door, Left
  • Measure resistance between the following terminals:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T019

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    6 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T020

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    4 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T021

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    6 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T022

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    4 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T023

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    6 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T024

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    4 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T025

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Vehicle with REC (Rear Electronic Module)
Yes: No:
T026

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Remove electrical component from socket:
    FR23 Fuse
  • Measure voltage between:
    FR23 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T027

Check: Interruption of Voltage Supply Circuit
  • Remove electrical component from socket:
    F55 Fuse
  • Measure voltage between:
    F55 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T028

Check: Interruption of Voltage Supply Circuit
  • Remove electrical component from socket:
    FB6 Fuse
  • Measure voltage between:
    FB6 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T029

Check: Vehicle Configuration
  • Is the following component installed?
    S221RL Switch - Window Lifter, Rear Door, Left
    4 terminals of the 6 -terminal wiring harness connector are used.
Yes: No:
T030

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    S115 Switch Unit - Driver Door
  • Ignition ON
  • Measure voltage between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T031

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Connect fused jumper wire to:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 10
  • Measure voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T032

Check: Short to Ground of Voltage Supply Circuit
  • Check the following component for proper operation:
    Fuse of the fused jumper wire

Test okay?
Yes: No:
T033

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Vehicle with REC (Rear Electronic Module)
Yes: No:
T034

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Front Electrical Sliding Roof
Yes: No:
T035

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

4 Doors
Yes: No:
T036

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X131 Rear Electronic Module
    (Wiring Harness Connector XR5 )
    &
    M1_M16 Motor - Sun Roof
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T037

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T038

Check: Short to Ground of Signal Circuit
  • Disconnect wiring harness connector from:
    S112P Switch Unit - Front Passenger Door
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T039

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Front Passenger Door Handle Illumination, Driver Door Handle Illumination
Yes: No:
T040

Check: Component
  • Disconnect wiring harness connector from:
    E72D Lamp - Driver Door
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
    E72P Lamp - Front passenger door

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T041

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X131 Rear Electronic Module
    (Wiring Harness Connector XR5 )
  • Measure resistance between the following terminals:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T042

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    FE33 Fuse
  • Ignition ON
  • Measure voltage between:
    FE33 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    S221RL Switch - Window Lifter, Rear Door, Left
E002 Result: Defective Component
  • Defective component:
    M14L Motor - Window Lifter, Rear Door, Left
E003 Result: Interruption
  • Circuit interruption between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
E004 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    M14L Motor - Window Lifter, Rear Door, Left
E005 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session

or

  • Defective component:
    S115 Switch Unit - Driver Door
    or
    M14L Motor - Window Lifter, Rear Door, Left
E006 Checking Procedure Validity
  • The selected Checking Procedure is not valid for this vehicle configuration.
E007 Result: Interruption
  • Circuit interruption between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
E008 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    M14L Motor - Window Lifter, Rear Door, Left
E009 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session

or

  • Defective component:
    S115 Switch Unit - Driver Door
    or
    M14L Motor - Window Lifter, Rear Door, Left
E010 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
E011 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 5
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session

or

  • Defective component:
    S115 Switch Unit - Driver Door
E012 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
E013 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 2
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session

or

  • Defective component:
    S115 Switch Unit - Driver Door
E014 Result: Interruption
  • Circuit interruption between:
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 4
    &
    Ground
E015 Result: Interruption
  • Circuit interruption between:
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 13 (XR3)
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    X131 Rear Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E016 Result: Defective Component
  • Defective component:
    X131 Rear Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E017 Result: Interruption
  • Circuit interruption between:
    F55 Fuse
    Output contact
    &
    M14L Motor - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
E018 Result: Interruption
  • Circuit interruption between:
    FB6 Fuse
    Output contact
    &
    F55 Fuse
    Input contact
E019 Result: Interruption
  • Circuit interruption between:
    G1 Battery
    Wiring harness connector (wiring harness side) terminal 30
    &
    FB6 Fuse
    Input contact
E020 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 24

or

  • Defective component:
    S115 Switch Unit - Driver Door
E021 Result: Short to Ground
  • Short circuit to ground between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 6
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 25

or

  • Defective component:
    S115 Switch Unit - Driver Door
E022 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 6
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 25

or

  • Defective component:
    S115 Switch Unit - Driver Door
E023 Result: Short to Voltage
  • Short circuit to voltage between:
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 3
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 24

or

  • Defective component:
    S115 Switch Unit - Driver Door
E024 Checking Procedure Validity
  • The selected Checking Procedure is not valid for this vehicle configuration.
E025 Result: Defective Component
  • Defective component:
    S115 Switch Unit - Driver Door
E026 Result: Interruption
  • Circuit interruption between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 10
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
E027 Result: Short to Ground
  • Short circuit to ground between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 10
    &
    S221RL Switch - Window Lifter, Rear Door, Left
    Wiring harness connector (wiring harness side) terminal 1
    &
    S221RR Switch - Window Lifter, Rear Door, Right
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    S221RR Switch - Window Lifter, Rear Door, Right
E028 Result: Defective Component
  • Defective component:
    X131 Rear Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E029 Result: Interruption
  • Circuit interruption between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)
E030 Result: Defective Component
  • Defective component:
    S112P Switch Unit - Front Passenger Door
E031 Result: Defective Component

If the nominal value is reached during one of the measurements, there is a short to ground in the circuit behind the component that has been disconnected immediately before that measurement, or the corresponding component is defective.
E032 Result: Short to Ground
  • Short circuit to ground between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session
E033 Checking Procedure Validity
  • The selected Checking Procedure is not valid for this vehicle configuration.
E034 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 39 (XE2)
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26

or

  • Defective component:
    X125 Underhood Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E035 Result: Defective Component
  • Defective component:
    X125 Underhood Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.





C-005 Rear Left Window Lifter Circuit > < C-003 Window Lifter, Front Passenger Door Circuit